Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi support team
I'm now based on ncs1.9.0 platform. I check the file "\nrf\samples\bluetooth\direction_finding_connectionless_tx\README.rst", finding that the board nrf52811...
I am working on a project with nrF9160dk to connect with AWS IoT cloud, when I was trying to update the certificate by using LTE Link Monitor, why I am getting errors when...
Hello, I tried to using the nRF Connect SDK with VS Code, however when it seems there are some problem while I trying the build. I have read the similar post and trying to...
Why is it that when I try to build assert_tracker_v2 for thingy53_nrf5340_cpuapp or nrf5340dk_nrf5340_cpuapp I get:
Blinky builds fine.
Also, cleaning projects tend...
Hi,
I've made my own PCB with an nrf52840. Right now I'm hoping to test out the bluetooth and measure my board's power consumption - the only problem is that I can't reliably...
Hello,
I can not find a good example online on how to properly configure nRF9160 DK for i2c. In order to learn the system, I am testing a simple example with the nrf9160...
I just install the NCS in toolchain manager, but after installation, only one toolchain folder is there,no zephry,no examples,
I'm going to play in VSCode.
what should...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough "RSSI > -45" and initialize...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement my firmware which will consume less current. I have implemented...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. Our custom board has a connection to nRF GPIO...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We need to publish the JSON messages larger than...
Hi, I am developing my own application using the SDK v1.8.0 with Demo direction_finding_connectionless_rx. I notice that in the
cte_recv_cb callback function, the rssi...
Hello,
I am using nRF 52840 DK board and using nRF52SDK17.0.2. I am trying to advertise data in GAP with the name " IG_Last4CharMAC_RFL " for example " IG_4DA8_RFL " but...
