Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I'm starting a new product development using nRF52832, SDK 17.0.2 and softdevice S312.
Should I use v6.1.1 or v7.0.1 of S312?
Nordic's docs for SDK 17.0.2 state that S312...
I have no idea about how to read the device id of the external flash in the nrf52840dk? Please guide me to do so.
I also referred the MX25R6435F datasheet, to see the method...
According https://infocenter.nordicsemi.com/topic/ref_at_commands/REF/at_commands/nw_service/xrai_set.html control plane data only are supported.
How to set PDN to use control...
Hello, I need a reference PCB layout for the nRF52810-CAAA WLCSP-33 chip. There doesn't seem to be a reference layout for this specific chip. Furthermore it differs from the...
Hi everyone,
I have a couple of Laird BL653 boards which use the nRF52833 chipset. They have SoftDevice S140 v7.0.1 on them and I'm using the nRF Mesh v3.1.4 for IOS. The...
On an NRF52811 (and I've had a similar problem on a 52833) I'm unable to use the NVS subsystem. Everything inits fine but there is a fault when writing to NV. If BT is disabled...
Hi Nordic team,
We have tried using Bluetooth peripheral HID keyboard example from nRF5 SDK and found an interesting problem.
In our setup, nRF52840DK is running the provided...
Hello all,
I have trouble reading saadc data with an amplitude of 10 µV - 100 µV with a sampling rate of 1K Hz by using nrf52832. I was wondering if I could get advice/help...
Hi,
The code is working normally, but when I include ble_radio_notification_init functionality. Then it crashes (hardfaults), on some boards not all.
[19:18:40.550]...
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). SES used Printf as a comment display and output it to the Terminal Emulator. I...
I've previously used Getting Started Assistant to install nRF Connect SDK 1.5.0 on macos and managed to get a complete and functional install.
I'm now trying the new Toolchain...
HI,
I have few queries regarding nRF52805.
Is there any specific pin configuration required to enter nRF52805 in to programming mode?
What is Adverting connectable...
Hello. I am conducting experiments with data transmission via the Enhanced ShockBurst protocol with BMD-340 modules. Transmission parameters: 2 Mbit radio channel speed, 512...
Hello Sirs
I want to use the serial port of nrf5340-Dk to get some serial data from a sensor and transmit this
data Via a peripheral connectable config by nrf5340-Dk ...
I'm trying to access an SD card with FAT_FS, with no success. I hooked an analyser to the SPI, but it's completely dead. I'm using NCS v1.6.0.
Is there something...
