Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
Hi,
We've been developing our application using pc-ble-driver which communicates with a PCA10040 devkit with SD API v5.1 connectivity firmware. In this dev environment,...
I'm trying to connect to a few sensors on the Nordic Thingy:52, and it fails with the following message: characteristic is not defined. The connection to the Thingy is established...
Hi,
i use nrf51822 and sdk 11.0 . I am using the ble_app_hrs_c example .This product consists of two devices，One master and one slave.
The master chip is nrf51822...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and made a custom FW based on the ble_app_hrs example. My custom HW has a 64MB S25FS512S flash memory chip.
I found...
Hi,
I am currently trying to run the DFU over UART example using my nrf52840 dk. I am using sdk v15.2.0. I followed the following instructions found in the Nordic Infocenter...
I have done a DFU code in our Customized board using NRF52832. My program was running successfully in nrf52 DK but in our customized board it's not working
While uploading...
Hi, I have a BME280 sensor running normally with the nRF9160 on v1.2.0 firmware. When I updated the firmware to 1.3.1, I had to update the code to run I updated the files...
Hi, I have a simple voltage divider circuit and I am measuring analog input from in between the resistors. I am using a custom NRF52832 being powered by a DK. I get quite...
I recently purchased a Thingy91 and have been following the start up guide but have been running into an issue with the thingy91 being recognized over USB. I was able to connect...
Hi Nordic,
I am developing a distance measurement application between the nrf52840 and nrf52833 unit for the long distance mode.
for the nrf52840 as center which running...
HI
I'm using SPI connecting to mutiple max31856(two now) on nrf52DK and SDK15.3
so I control my ss pin to pull low by myself
chip select by changing spi_pin like some...
a data array, length is 2048,use function "sd_ble_gattc_write", a error occurred, length less than 240, no error.
do {。。 err_code = write_configure(m_center_handle,14...
Hi all,
I'm using NRF SDK v17.0.2 and IEEE 802.15.4 stack library. I want to implement sleeping device. I think I should use sys_sleep_request_ms function to make the device...
