I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hello,
I'm designing the electronic of the nRF9160. We use the ANT PIN (61) for frequencies in the range [700MHz; 2200MHz].
I'm wondering to add a band filter on the...
SDK16.0.0, S132v7.0.1, nRF52840
We call nrfx_uart_tx() from the main application (non-isr) context to initiate multi-byte data transfer from a queue we manage.
We also...
I am using guide provided at https://openthread.io/guides/border-router to create border router. I am using Ubuntu 18.04 on a PC. I tried same on RPi 4 too and seeing same...
Hi !
I'm setting up buttonless DFU on an nrf52832. I'm using SES on windows.
I found two ways of performing it, one in the forum and another in the infocenter.
The first...
Hi,
we have to program direct test mode software for our certification process of our device. What we did was: take the dtm example from Nordic SDK (v15.3.0) and programmed...
Hi everyone,
I am desing a low power BLE application using the nRF52840.
How do I restart the advertising after the APP_ADV_DURATION has been expired?
Thanks in advance...
Hi,
We developed a medical device based on the nRF9160 chip and we would like to do the EMC test for qualification. Does Nordic provide any examples or support for the firmware...
Hi Team,
I have flashed the given serial LTE Modem hex file(attached) into dev kit nRF9160 and tested TCP server mode.
I am facing issue with AT command: AT#XBIND=3442...
Hi,
I´m using nrf52833 on customized board with a sensor on it. I would like to send the data, collected from sensor ober ble to nrf connect app. I print the collected...
Hi community !
i'm working on nRF52840 DK. We'll put SoC into a device where we couldn't have access with a cable. So my questions are :
1) Does DFU example use OTA to...
Hi,
I have to use current time service and one other customized service in my project.I am able to advertise only one service i.e customized one.can you please let me know...
Hi,
I am working on the nrf52840 DK using "nRF5_SDK_16.0.0".
I tested out the example code for USBD Audio in "examples\peripheral\usbd_audio".
If I use the default values...
Hello. I evaluated the effect of temperature and humidity on BLE connection stability. I thought that the effect of humidity was higher than that of temperature, but the effect...
I'm trying to rate nrf52832 now. I'm using Keil uVision5 as my development environment.
I have written softdevice s132_nrf52_7.0.1 for the target.
I'm trying to set the...
Dear Sirs:
I use 52832, and there is 512KB internal flash.
So, I am wondering if I could have my own flash partition as below.
- Bootloader (w/ capability of firmware...
