I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
I want to use the four peripherals UART0, UART2, UART3, and I2C_1 on nrf9160. When I was building the project, I encountered the following error.
Here my prj.conf
...
Hi,
I received a Thingy91 and am unable to commission it to nrFCloud.
The Thingy91 skipped orange breathing as mentioned in the manual here (step 4). It went directly...
Hi! I'm running a project with an nrf52 chip for which we use the JLink as the interface. I've been using my setup a lot for the past year. The other week, every LJink command...
Hello,
i'm trying to understand how the management of the SS pin is (or has to be) performed when using nrf9160 as SPI master.
In this post Håkon said that:
"Most driver...
Hi,
I using the radio test example on the pca10040 with nrf52832 EVB.
And set the radio test to Tx, the parameter as below:
Data rate: NRF_RADIO_MODE_BLE_1MBIT TX power...
I have searched the devzone and couldn't find any solution
followed the instructions from Nrf Connecta dn verified as well.. using
tag v1.1.0 (have done west update...
I'm using the MESH SDK 4.2.0 on a nrf52832 in combination with the Serialization interface (ACI) example
We'd like to implement the key-Refresh cycle and are planning on...
I am trying to setup (Nordic Edition) SES 5.10d for an example to download to the nRF52840 Dongle.
The tutorial* helpfully discusses how to avoid overwriting the MBR and...
I am using nRF52840-CKAA-R7 II2c to connect to my MSP430 i2c[ slave]. i have put any pullup on the clock and data thinking, to use nordic pull up in default. clock is connected...
Hello, all ..
I'm using nrf52 pca10040, s132..
I connected custom board and nrf52, and would like to communicate with uart. First of all, custom board is model cm1106...
I am looking to write my own IRQ handler for the UART. I read the post https://devzone.nordicsemi.com/f/nordic-q-a/46822/nvic-table/184731#184731
and added my own definition...
Hello,
I am new to Nordic and Segger. I am trying to build source code developed by a 3rd party. It was originally developed with GCC in Linux. I have followed some suggestions...
Hi,
I am working with nrf52840dk and using a peripheral _uart example from NCS v1.3.0. and the problem that I am currently having is that I cannot get it to low power. At...
