hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi Sir,
My project need LESC & AES-CMAC function, then I enabled below CONFIG in sdk_config.h :
NRF_CRYPTO_BACKEND_MBEDTLS_ENABLED
NRF_CRYPTO_BACKEND_MBEDTLS_ECC_SECP256R1_ENABLED...
Hi,
So I am trying to configure the stdout console to use UART1 by default. Using the NrfConnect menuconfig in Segger emStudio I can set it to use UART1 with the following...
Hello !
I have read in DevZone, but still not sure regarding nRF52832 .
For nRF52832 and page size 4k, and regarding only writing zero-bits.
Can I in same page perform...
Hi team,
Here is the previous ticket
https://devzone.nordicsemi.com/support/234693
One of my customer TMC is using our nRF52810 in a BLE key project for central role...
When in dfu mode (with usb dfu enabled) if we jump to application via "
nrf_bootloader_app_start" there seems to be an issue where the firmware locks up and doesn't start...
Hello
my setup is a nrf52840, the sdk15.3, Softdevice s140.
is there a possibility, maybe with freertos, to to run two seperate applications like two threads.
In the...
Hi,
I'm trying to implement a slow timer which is supposed to be triggered about every 30 minutes or even less frequent, but I'm kind of clueless how to solve this issue...
from which antenna these values were derived resp. measured? e.g. there is a pcb antenna and a hirose u.fl connector available on pca10040... examples/ble_peripheral/ble_app_eddystone...
hi,
The software version is nrf5SDKforMeshv310src and nRF5_SDK_15.2.0_9412b96
I use five nRF52832 nRF52 DK. client * 1, server * 4, provisioner by android phone.
examples...
Hi can you help to configure nrf52840 DK board to measure power consumption with keysight n6705C. In manual is described with ammpermeter and oscilloscope. Keysight n6705c...
Hi, I'm new here so please let me know if any additional information could help.
We are in need of encoding speech on a nRF52840 and are working in Opus and are having trouble...
Im getting this error any idea how to solve it this are configs.
Loading solution lte_ble_gateway.emProject
Executing load commands
/usr/local/Cellar/cmake/3.15.2/bin...
If the only supported method is through the PC-based nRF Connect Programmer GUI application, how is a system based on nRF91 its modem firmware once deployed in the field ...
Hello,
I am working on nRF52832 SDK 15.3.0 using segger embedded studio in windows 7.
I am trying to merge two application, one is launch application through NFC and...
