I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
Hello,
I'm developing a custom application based on SDK 15.2 on nRF52 using softdevice S132 v6.1.
In my development, I want to ensure timestamp synchronization between...
Hi,
I am using NRF52 SDK 15.3 on nrf52840 Preview DK
I am using BLE to transmit data, I want to use PPI to get readings off of SAADC but using 'app timer' instead of TIMER...
I'm currently on a question for which the documentation here can't help me.
If I'm correct, the Dual-Bank Update allows to retain a safe copy of the old firmware image...
Hi,
I am using esb project of SDK15.3 to test esb PTX and PRX function.
The default setting of address-0 and address-1 is 0xE7E7E7E7 and 0xC2C2C2C2, and PTX and PRX can...
Hi,
1.I want to develop the my product using nrf51822 with PCB antenna(as shape given in sdk hardware) with following board stackup-
2. i am going to use cap-0603 in...
Hi,
I am using nrf52840 S140 PCA10056 SDK 15.2.0 version with example ble_app_multirole_lesc_S140_PCA10056 . i am using Segger Embedded studio IDE. So now problemis i am...
Hi,
I am trying to get my systemOFF current below 1uA, but Im struggeling.
normally I use MBED, but to eliminate that variable, I just did a test without MBED, I took...
Hello together, I am experiencing problems with the nrf52840. I got the BLE_APP_Blinky example to run. Now I am trying to get the BLE_THROUGHPUT example experiment to run...
Dear nordic,
I want to know something regarding your SDK. I have nrf52832 development board and i use sdk 15.2 .
1. if i want to use BLE 4.2 version what changes i want...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I added the UART example to...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I used the nRF UART and nRF...
Dear nordic,
I need more information regarding this?
1. I heard the BLE one packet has possible 20 bytes. but i tested this example and connect using nRF connect app...
Hello everyone,
I am experiencing a weird problem; I am working on an NRF52840 DK board and writing my code in Segger Embedded Studio.
I do not have any problem when...
