I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
The pin connected to lis2dh12's int pin consumes about 300 uA.
But the pin I used as button,also enabled int function , works good.
The pin I used as wake-up is in input...
In order to establish a wireless connection from my pca10056 developing card and a second nRF52840 SoC module using example CLI commands, and then being able to check/set...
Hi,
I have few queries regarding the internal regulators of nRF52840.
1) Is it mandatory to configure the internal LDO or DC/DC regulators of nRF52840 ?
2) If these...
Hi,
As mentioned in the Ch. 5 "nRF52840_DK_PB_v1.0.pdf" Section 5.3 in "high power mode the external supply should be connected to just the "VDDH" pins and "VDD" pins not...
I want to write to nRF52840 the example "ble_app_hrs_pca10056" from nRF5_SDK_15.2.0 by command line.
first I merge 3 hex file (bootloader, softdevice and app) with the command...
Hi,
I'm developing BLE 5.0 applications as a peripheral on nRF52832 under Windows, based both SDK14 and SDK15 (Softdevice S132).
I don't have any smartphone that supports...
Hi every body,
There is a problem with pwm driver example in demo3 part! after downloading, the board led is just on as it must, but after changing top_value there is no...
Hello everyone, I am planning to use the nrf52840 with the ECG sensor ads1298 (AFE for 8 channel ECG). The sensor interfaces via SPI to nRF52840. Has anyone worked on ECG...
Hi all,
I am working on nRF52832, nRF5_SDK_15.2.0, nrf5SDKforMeshv300src, softdevice_6.1.0 and communicate with CAP1214 device.
When I erase all flash on nRF52832 and...
Hello all,
I am using nRF52832 IC, Segger ES as IDE, SDK 14.20 and SD v5.0
I have around 70 bytes of data to be sent to a smartphone. I am using nRFConnect app to check...
Good afternoon. I need to make a network 5 or 6 nrf52840 boards connected as peripherals on a single central board, also of nrf52840. Each board will read a sensor, and send...
because I cannot find nRF module for testing.
and I want to use bluetooth 4.0 BLE with nRF uart
so my product will send data from serial port (rx ,tx through DB9 ) and...
Hi there, We are not using external Crystal for this design and thinking of reusing XL1 & XL2 (Pin 0 and Pin 1) for SPI (MISO & MOSI). But I found that I can't set properly...
So we're in production with the '832 and me, I drank the kool-aid already, but I'm trying to turn my cow-workers on to Nordic so I tell one of them "Oh install the command...
