Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi ,
I am trying to integrate LSM6DSL to BL5340 module(laird connectivity) through SPI but I am getting failed on initialization. I am noob to NRF so could someone please...
Hi all,
I've build my own board with nrf9161 LACA, so for now I've tried to create my own board, for the moment I'm just trying to pilot my 3 leds. I've follow dev academy...
Hi, I'm building an application that will use the nrf9160 as a middle man for a websocket connection that becomes a uart connection on the main processor. Thus I want to receive...
Hello there! I am working on a central-peripheral connection, where sometimes the central is not receiving notification(s) from the peripheral. The central then asks for a...
Completing the nRF Connect SDK Fundamentals in the DevAcademy, I stumbled across this question:
Why is true not a valid answer here? Running gpio_pin_set_dt(&led, true...
Hi,
I was following the beginners tutorial and things were fine till i reached the section to create a project from scratch. I was able to build this project as well.
...
Hello,
I'm curious if there is a dependency to use the same Bluetooth module to perform OTA. If I created my own custom board, would I need to use an identical Bluetooth...
I have followed the procedure given at following url https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/create_application.html and created a application(based...
Hello,
I am working with the Signetik M1-N1 module, which is using the nRF9160 chip, as well as the DEV-M1-N1 breakout board, for evaluation and development:
Since this...
Hi,
I am working on a project that uses nrf52833 as one of I2C master to communicate with few I2C slave devices. Meanwhile there is another MCU (stm32H7) on the same bus...
Hi,
I am looking for a sample programs for my use case, wherein :
1. I have to encrypt & store the DFU image which is present in secondary partition.
2. Decrypt the...
Hi,
I am trying to mount Fat FS using pm_static.yml instead of devicetree overlay fixed partition. I can generate a memory report, but when I try to mount file system I...
Hello All,
I have a very strange problem and i can not found any solution.
I have NRF52833DK and NRF52840DK where mi code is working perfectly. Compiled with OTA is ok...
According to the docs, when CEDRXS=3 is sent to the 9160, the modem disables eDRX and the unsolicited response code. However, this means there is no response code to listen...
