VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hello, I am developing with nRF5340 with my custom board. I observed a high current consumption when the network core is flashed with the ipc_radio image. I am developing...
Hi I want to use nRF9151DK and i have jio NB-IOT sim card.
I flashed asset tracker application from quick start and it is not working or connecting to internet this is the...
[Environ] nRF Connect SDK v3.2.3 nRF9151 (Custom board) VSCode (1.115.0) Board target: board/nrf9151/ns
When using the PTI firmware, the AT command resulted in an error...
I have a PCB with nRF52833 and nPM1304, I assembled 3 identical PCBs, 2 of them work 1 does not I am using 2 available Buck coveters, first outputs 1.8V for powering IC on...
Hi,
I a\m looking for your recommendation on screen to use with nRFLM20DK board to experiment with LVGL display. Assuming that latest version of nRF Connect SDK has everything...
Hi,
I am using nRF5340 (CPUAPP) with MCUboot and Partition Manager (pm_static.yml, CONFIG_PARTITION_MANAGER_ENABLED=y ).
Build and flash are successful, but during debug...
Dear Technical Support Team,
I have recently been developing with the nRF54L15-DK development board, using the official channel_sounding/cs_test example provided by Nordic...
I am designing a battery system with can charge or supply power via a USB-C PD controller. It will operate up to 20V. I want the option to connect this USB-C D+/D- to the...
Hello, I was able to flash the firmware built using the samples provided by the "nrf connect sdk" using VScode. But, I see failure when I tried to program the nRF54L15 with...
We're dimensioning the pullup resistors for the lowest possible standby current in system-OFF, but we cannot find any leakage current spec in the nRF54LM20 PS / datasheet...
When the USB stack and your local Filesystem code both try to control the flash chip simultaneously, the system will crash or trigger a HardFault, causing the restart.
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
I was trying to flash a program on nRF52833 development kit and got this error, it important to notice that my college was trying to flash (via VS code) it before and I am...
Hi,
I'm working with the nRF54LM20 DK (nRF54LM20A) and evaluating whether it can act as a USB host to read data from an external USB CDC ACM device.
The intended setup...
