hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
We are in the feasibility stage of a product that requires integration of both the Apple "Find My" and Google "Find My Device" technologies.
Based on my research...
hi
We are developing with Segger embedded studio.
.
If you copy and move the SW development project folder to another PC, the following error occurs.
(Only occurs...
Hi,
Very beginner to this so bear with me.
we are testing an asset tracker which uses edrx. The asset tracker can receive a wake-up sms command.
However the network...
Hi,
I have ported my already working nRF52840 SPI slave code to a nRF5340, but it doesnt seem to receive any data. I have verified the CS, SCK and MOSI signals, but no MISO...
Hi,
I was wondering, what is the professional, assembly line ready procedure to program the IMEI on an nrf9161?
So far, I've only found rajeev's post in this discussion...
Hello,
I am using a Raytac MDBT50Q (nRF52840) on a custom board , and I am trying to blink an LED, but it is not working.
"I need urgent help as this is blocking my...
We can get BLE address in adv report: How to get mac address of nearby ble devices? - Nordic Q&A - Nordic DevZone - Nordic DevZone
At that moment, peripheral not connected...
I have download this .zip from the Nordic site. I am a beginning coder and I am using AI to help assist me on my project and learning C code. I seem to unzip the file correctly...
Hi, I am trying to understand periodic advertising and some basic questions:
I am using periodic_adv example from the NCS.
I see teo ADV data defined in the file as...
NCS 2.7
NRF52840
SPIM3 at 32 MHz.
I have CONFIG_NRF52_ANOMALY_198_WORKAROUND=y and have confirmed the workaround is being activated by setting breakpoints in my code...
Dear,
I need to generate a pulse signal on one IO following this pattern: HIGH for 12us ; LOW for 106us ; and so on...
I tried to use TIMER0 with NRF_TIMER_EVENT_COMPARE0...
Howdy,
I am using an nRF52840 to perform BLE communication. For this communication I am using extended advertising to perform most of my data transmission. Thing is though...
Hello, i have a device supporting DFU OTA i'd like to create a small tool for flashing firmware from the computer to the device. I've set thr device to DFU mode. Is it possible...
