Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
hi support team,
customer is asking how to add keep alive time in https request header,
i was trying to do this command as below: adding " Keep-Alive: 60\r\n" in XHTTPCREQ...
Hi there!
I've been digging through the code base but could not find a compile option to enable LOG_DBG() type output so that I can observe the JSON formatted packets sent...
Hi,
1. Please solve the problem of high network current registered to nRF9160 (test environment: no network signal)
2. Rf signal: the test current is normal. See Appendix...
Hello,
I implement my own DFU master in nrf52 using SDK11 to replace use of Nordic mobile App. Target to upgrade is also nrf52 but with SDK15.
I have difficulty to get...
Hi,
How do I set the SPIM3 parameter so that MOSI is low after SPIM3 has sent a byte 0x01?
The test environment
DK PCA10056
SDK :sdk17.1
example :spim3
Thank...
Hi,
How to enable NRFX_LOG_INFO?
I ran the following test, but no nrfx log was found
example:D:\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056...
Hi
1.Referring to this tutorial, the customer tested the cat-m mode, and the equipment could not be identified by the customer instrument. How to deal with it?
2.nRF9160...
I followed the tutorial videos and when I connected the device using USB, the computer didn't recognize it and it didn't show up in the devices list in VS Code either. pc...
Hi,
I'm working on a project where we are receiving sensor data from a BLE peripheral (BL654), and publishing it to a piece of PC software via UART/ FTDI cable from a BLE...
hello
1.NRF52840 Upgrade APP+BL+SD from SD15.3 to SD17.1.
2.BL use pca10056_s140_ble_debug,APP use ble_app_buttonless_dfu.
3.Program batch file.
nrfutil settings generate...
I have a case where a maximum of 1.4V will be applied to an GPIO pin immediately before the MCU powers up (the voltage enables a boost converter, which then powers up the...
I see this message on my debug output whenever I connect an app to my device. I'm trying to find where the opcodes and status is documented but can't. Can you please point...
Hi, I'm using a nrf5340 custom board. In my program I am using MCUBoot but I would like to know how I can remove the second slot in flash to flash a big program. I'm will...
I have 4 Thread end devices commissioned onto a matter network and want to control these devices from another Thread end device by pressing push buttons. Is this possible...
Hi,
I am having some issues with the Co AP Client and Server on n rf Connect SDK v 2 . 1 . 2 .
I have flashed two n rf 528 40 dev kits with the examples , one with the...
