void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi! We're working on a BLE product which is intended for use in the US. This product uses an nRF52833 SOC, with some external components on a PCB we've designed with a printed...
I'm trying to evaluate a Nordic BLE module for a new battery powered project while waiting to establish a connection to a base station device. It seems like your lowest powered...
Hello,
When we tried to increase the Security level from SEC_OPEN to SEC_SIGNED_MITM, it will output error 0x6 which is "Not supported". So how can I do to support a higher...
We are developing AoA direction finding with nrf52833 and antenna array. We also want to include Wifi connectivity to our receiver, having nrf52833 + antenna array. Which...
Hello,
I want to perform NRF52840 Firmware update remotely. I refer to link .
I want only normal http OTA update without encryption for prototype testing. Is there any...
Hi, I've been measuring a nRF52840-powered prototype powered from a 3V coin cell battery. I would like to use High Voltage Mode with REG0 in DC/DC-mode for maximum battery...
Hi,
I am trying to implement the attribute reporting for a zigbee dimmable light device, reporting to the coordinator.
The code is based on the zigbee\light_control example...
MCU: nrf5340 Network Core nRF Connect SDK Version: 1.5.1 Currently there are multiple libraries under ncs/nrfxlib that have their own " nrf_errno.h" . Out of those libraries...
Hello,
i have a function wich just send "hello world" via uart0. static otError SendUARTCommand(void) { volatile uint32_t ret; const uint8_t message[] = "Hello World! \n...
Hi !
This is more of a question than an issue. I am curious about the future of TF-M and its implementation on Zephyr. Does anyone know what are the plans on Zephy's or...
I'm trying to set tx power to +3db in the peripheral_uart sample.
I don't need dynamic control, just setting to always use +3db.
Adding the following line to prj.conf...
Hi,
I am using coded BLE to connect two board using nrf52840. I just let bluetooth to run, then measure power consumption of the peripheral board by measuring the current...
Hi,
I am trying to send messages from my gateway, which has UART and __LOG enabled, to a specific LPN address (0003).
So I want to send messages from my FN Light1 (0002...
We have developed an application in ncs-1.3.0 where we created a west.yml file for the application that lists nrf, zephyr and other dependent repositories. We have downstream...
Hello. everybody.
I'm new to be here.
Now, I'm struggling to succeed in building 'ble_app_beacon_pca10040_s132.uvprojx'.
(This file located in C:\(private dir)\nRF5_SDK_12...
