Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I have developed the application code for light node in ble mesh network.
I was able to see this error quite often:
app_error_weak.c, 115, Mesh error 4 at 0x00000000 ...
Does the 9160 GPS module have a built-in LNA? Is it possible to adjust the GPS receiving sensitivity?
We hope that the wireless index of wearable products when worn on the...
The set up which are used are a nRF52840 dongle programmed through nRF52832DK's debugger. After executing "erase all" in Programmer app, which erased the bootloader, it's...
We are using NRF52832 based Module in our design. Currently BLE Services & characteristics used in our firmware: 1. Custom Service characteristic 1: 37 Bytes characteristic...
Hi,
I understand that BLE Logical Link Control and Adaptation Layer Protocol is responsible for protocol multiplexing capability.
Can you please explain what kind of protocol...
Hey,
when i call:
otLinkSetChannel(OTInstance, ThreadChannelToUse);
from the very beginning of the programm:
void main(void) { int ret; ret = InitLEDs(); InitTemperatureMeasurement...
We are using nrf5340-dk to communicate with nrf5340 custom board and trying to search for the other sensors' addresses. There is secure mode and unsecure mode CPU. Which mode...
Hi.
My first attempt to get SAADC to work was:
NRF_SAADC->INTENSET = (SAADC_INTEN_RESULTDONE_Enabled << SAADC_INTEN_RESULTDONE_Pos) | //A result is ready to get transferred...
Hi,
Can I connect a 3.7V Li ion battery to the dongle VBUS keeping the SB1 and SB2 configurations as default?
Would this 3.7V applied to IC's VBUS pin cause any issue...
I want to view extended advertising, auxiliary advertising , LE coded data.
i had installed nrf sniffer app wireshark but it doesnt display this.
Ellysis bluetooth tracker...
Hello,
I am working on NRF52805.
I am able to debug my program with J-link using SEGGER.
However, when I try to download the program it seems like it is not running...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central.
Is it possible to change the Tx Power while connected to the device? I made it possible to change...
