void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello, I want to use the nRF52820 as a slave device. I've left my code, prj.conf, and DTS files below, but the spi_transceive function seems to be getting stuck. What could...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
nRF54L15 LE Audio with I2S interface, LC3 codec point-to-point audio The specific flow is as follows: The nRF54L15 communicates with the mic via I2S to capture audio data...
I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Hello, we use nrf52832-ciaa in our project and it is light sensitive. Could we use x-ray to inspect soldering quality or it will damage the mcu? Thank you, Anton
I tried to find an explicit statement whether a new IMEI needs to be written to nRF9151.
These sources state that nRF91x1 ships without IMEI and it needs to be written:...
We are working with Nordic’s official peripheral_esl ( https://github.com/NordicPlayground/nrf-esl-bluetooth/tree/main/samples/peripheral_esl ) sample application for Electronic...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hi,
We are working on a project using the nRF5340 Audio DK. We want to take user input either from UART or BLE, and switch between them based on the connection status. ...
I would like to know the approximate flash memory footprint required to implement BLE Mesh, Zigbee, and Thread , individually. Could you please provide the details for each...
Hello,
I've been trying to use the NRF Cloud A-GNSS capabilities using the location library. However, after carefully checking the documentation, I am still unable to do...
I have a thingy 91x and am trying to get the fuel gauge on the sample code working. It doesn't include the thingy91x as a sample of this, but is it still possible? As I know...
Hello forum ,
here i m using nrf52840 where it is customized board ....i tried to print jedec number for windbond w25q64 here this code prints the jedec number and also...
I am trying to interface the PDM mic (Link : https://www.adafruit.com/product/3492) with NRF52832 Devkit. I am using PIN 27 and 26 for Clock and Data Respectively. I can see...
