here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi
I'm trying to run some power profiling with basic BLE apps on nRF5340DK in conjunction with PPKII. Saw several videos in the on-demand webinars section on PPKII and power...
Hi, all.
I'm in trouble in solving a question when i learned NRF52832 recentlly.(SD s132, V5.0, SDK15.0)
I want to read the temperature data from the sensor on-chip and...
Hi,
We widely use this MCU on our products.
Last batch with Rev-D has many issues with burn process.
I'm attaching 2 screenshots along with logs of the problems.
Hello everyone,
I have one or two questions regarding some evaluation measurements on the nrf9160 module. I would like to evaluate the matching network of our nrf9160 antenna...
We use nRF SDK5 17.0.2 with Softdevice S140 on an nRF52840-DK. We have a firmware that we always want to start in DFU mode, then use the abort command to be used to start...
Hi,
I want to read the temperature data from the sensor on-chip and send it to my phone by bluetooth. But as said above, after the connection between my nrf52832 module...
hi all, i'm here to ask few questions on how to get CTE packets. 1. which example can i start off by adding ?
2. can i use dtm to send CTE packets? if do, how can i do that...
I verify the TLS connection without a certificate in the matt_samples routine. I found that the connection to the server is very slow, it takes more than 20 seconds, how can...
Dear Team,
i have connected a sensor to nRF52810. The sensor power suppply (VDD) is connected to one of the GPIO. My system will switch between systemON and systemOFF most...
Hello
We are just now looking at the implementation of a Bluetooth module for our product and we have previously looked at your module called nRF 52.
I would need some...
Hello Nordic Team I want to use the ble_app_eddystone example found in SDK 15.3 on NRF52832 to advertise in connectable mode from the beginning. I tried to add nrf_ble_es_on_start_connectable_advertising...
Good day!
We have six of the nRF52840-DKs and would like to try coded PHY mesh communication. Is there a link for the SDK which features coded PHY (long-range) mesh? Apologies...
nodic example in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_lbs , ,i can not find the software interface place in peripheral_lbs example code from where to send
