Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
In the Enhanced Shockburst User Guide, there is a brief discussion about the required bit pattern of 1st on-air byte of the base radio address
(which immediately follows...
If I use nRF Connect to connect to the Peripheral and the Subscribe to Notification Characteristic I can see in the "Enabling notifications" in the log (however no notifications...
Hello
I use sdk v17.0 and nrf52832.
I'd like to use 1-channel PWM and 2-channel PWM. However, an error is output from the pwm_enable when using these two together.
...
Hi,
Following are my working environments:
Product: nrf51422 Evaluation Board
SDK: nrf5 SDK v10.0.0
IDE: Segger Embedded Studio
Programmer: Segger J Link
I was...
Hi,
We have a device that is using Nordic's ESB protocol. We want to use different frequencies to avoid collisions and for that we also need dynamic frequency handling....
Hello,
I have two questions:
How do I access the gpio pins of nrf52840 dk? what example program from nrf5 sdk can I use as example?
Is there a simpler example program...
Hi engineers,
This is my timer init code. I place it before functions timers_init() and ble_stack_init().
app_init() includes led and timer init function.
Cheers...
Hi all,
I am now evaluating the BLE 5.1 supported chips. I see that s140 support ble 5.1 but I see nrf52840 can't support aoa. Is that I need to use nrf52833 with s140 softdevice...
I have tried this demo (SDK17) on a few different Windows machines and they all give the same error for me. On plugging in the SDK after loading the demo Windows tells me...
There is a similar case where the user mentions that he fixed his issue by "changing the compiler" with no further explanations. https://devzone.nordicsemi.com/f/nordic-q...
Hi
I am using nrf52832 (S132) with SDK17. I want to store some data in the flash memory dynamically. So what would be the maximum and minimum flash memory that I can utilize...
I would like reduce TX Power in DFU secure bootloader, I would like use sd_ble_gap_tx_power_set function but I faced with the following problem, I don't know how to get conn_handle...
Hi
I am working on the GPS for Thingy91. The Thingy91 is able to get the fix when I am outside and test it. However, when I am in the building by the window or on the balcony...
Hello ,
I am bit confused about the minimum and maximum connection interval . what does mean ? it is time interval for the connection or else time interval for the data...
Thanks in advanced. Platform is nrf52832, SDK_17.0.2, use nrf connect app. I create custom service. If I set 128bit base uuid: {0x9E, 0xCA, 0xDC, 0x24, 0x0E, 0xE5, 0xA9, 0xE0...
