Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello, It is my first time running FreeRTOS on NRF52 and I would really appreciate any help to figure out the root cause for the hard fault. I run a simple FreeRTOS application...
nRF52832_XXAA, S132 v5.0.1, SDK 14.0.0
We enable SoftDevice via nrf_sdh_enable_request(). We immediately assert nrf_sdh_is_enabled() so we know it worked. On the first...
I recently got a custom board manufactured using an NRF52840 with the TI AN043 antenna to find that everything worked except for the bluetooth antenna. So I'm here to seek...
Hi,
I was able to successfully complete Figure 2 on page 6 of nRF_Sniffer_UG_v2.2.pdf, and successfully loaded and ran sniffer_pca10028_1c2a221.hex.
I rebooted my computer...
Hi,
We’d like to migrate from nRF51822 to nRF52 series. We have 2 targets : nRF52811 and nRF52832. We’d rather use nRF52811 (better sensitivity, lower consumption, features...
Hello
I'm trying to send an uint16_t array with 750 elements over the NUS service.
To do so I fill the data in multiplle uint_8 arrays of length "m_ble_nus_max_data_len...
Hi All,
I've got an nRF 52840 PDK and I'm connecting a GPS module ( Adafruit Ultimate GPS Logger Shield ) to it to read the data using nrf_serial.h library. I get about...
Hi
I am working on a project that has two timers, TIMER3 and TIMER4 (TIMER3 as timer and theTIMER4 as a counter). TIMER3 resets after counting up to 4. I am using PPI to...
Hello Nordic Team,
I was working on blinky_systick Example(Path - nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky_systick\pca10056\blank\ses)which is available for...
hi...
i am using mesh 3.1 latest version , i have changed the light switch example code , where i am sending the character . i have completed the scanning , provisioning...
Hey. I'm looking for a complete free RTOS for the commercial development of our startup. We will use the SEGGER Embedded Studio IDE and SoC Nordic nRF52840. As I understand...
Hi,
i'm current working on example light switch, when i use function generic_onoff_client_get(); in client to get status from server, callback function app_generic_onoff_client_status_cb...
We're running a multi-drop single duplex RS485 bus, so it's important to stop driving the bus as soon as a transmit is complete so the next device can transmit without two...
We're running a multi-drop single duplex RS485 bus, so it's important to stop driving the bus as soon as a transmit is complete so the next device can transmit without two...
