VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi
I am writing ANT+ device on pStorage and want to read back from memory during ANT+ stack init. I am trying to change the Device name on this snippet
No luck so...
Hi,
I'm working on the ble_att_mtu_throughput example code on nrf52840(peripheral) & nrf52832(central) . SPI data is transmitting from TI(slave) board to nrf52840(master...
Hi there! I am developing a device with the nRF52810 that requires the following:
Receive audio over BLE
Store audio in memory
Playback audio on command
Would...
SDK 15.2 API 6.10 SES custom board
I am trying to get DFU to work and it is not seeming to work right.
I am trying to engage DFU mode by holding in button on board for...
Dear DevZonee's
Im trying to esablish a BLE connection using the following configuration of the peer-manager:
* LESC
* Just Works -> IO-Caps none (0x03)
If i run...
Hello
I am using SDK12.3 on nRF51822 chip using Keil V5 on windows 10.
I am using experimental_ble_app_buttonless_dfu example and bootloader_secure example.
They both...
Hello!
SDK 15.3
If I build secure_bootloader example project using Segger Embedded Studio it works, I can see it nRF connect.
If I build it using armgcc it does not...
Is there any actual difference between "Fast Advertising", and "Slow Advertising" - or is it just a way to easily specify two different sets of timing parameters?
The question...
Hi,
I'm having problems with the bootloader in SDK 15.2. I'm using an NRF52840, I don't know if the CryptoCell is giving me issues.
The DFU fails when checking the FW...
Hi All,
Sorry if this is a simple question, but I can't seem to find an example where the device is programmed as both RX and TX. (The examples have either one or the other...
Hello,
I am developing application which allows multiple central devices (phones) connect to a single peripheral device (custom board with nRF52840). I took example from...
We are under development on our custom board. then we suddenly were able to flashing the firmware, hex files onto our target board. SES showed the popup message such as "...
Hello,
I am unable to flash target board using my nrf52840 Dev board. I have two dev boards and I am able to flash the target with the other dev board.
The target board...
To what values should I set the PWMCON register to so that the PWM0 and PWM1 frequency is output at 20Khz with duty cycle varying between 1 to 2ms. Now specifically I am asking...
I am new to Bootloader and was going through the Secure BL example without SD but with UART
Here I observe that the Linker Option Shows the RAM and ROM address for the Bootloader...
