here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Using nrf9160 with W5500 Ethernet NCS Version 2.6.1
My normal MQTT connection is working fine, but connecting to aws is being an issue. I am getting mqtt -22 error. I...
Hi. I wrote a firmware on nrf9160(SIAA chip), but it doesn't work. On the hardware side, the circuit is same as that of nrf9160-DK, CTS and RTS is short respectively.
If...
Hi,
We are using two nRF54l15-PDF to communicate as SPI, one is in master mode and one is in slave mode. The master device sends a simple array of bytes, the first one being...
Hello,
I'm currently working on NCS2.6.0 and ANT sdk v1.3.0,
I would like to know is it possible to do BLE scanning(without connection) and ANT+ heart rate searching at...
I'm working on getting a radio test example project built for our custom board that is currently in production in order to perform some FCC testing, but I'm struggling to...
Hi everyone, this is more of a programming advice question: basically we have a "registration app" associated with our BLE product which will be used to communicate user details...
Hello,
I've been developing code on nRF9160 for a while. In the beginning everything was straight forward and working just fine also the code was pretty simple. Now like...
I am currently working with the nRF5340 and using NAND flash for data storage. With the current code size, I need to create a secondary partition in the external NAND flash...
Hi,
I am using nRF52-DK to program a custom board based on BC832 (nRF52832 SoC). I recently updated "nRF Connect for Desktop" and associated applications. I believe some...
Hi there,
I'm trying to get the entire toolchain running on a new Win 11 AMD machine. Visual Studio Code has version 1.88.0, toolchain has v2.6.0 and SDK v2.6.0.
Therefore...
Hi,
i am working on Pancake motor C0820B006F circuit and it is connected to P0.12 pin and ground iam usin NRF52 development board. i want to change the pan cake vibrator...
Hello
We developped a firmware on the nrf52840 dongle able to communicate with a Windows PC through the USB.
On Windows 10, we can communicate with a serial COM port....
Hi, we looking at converting our devices from a BLE communication protocol, to BLE LR with MESH networking.
Currently, we are doing the following:
Android tablet connects...
Hi,
we are ramping up production, and need to make many production jigs, and programming in parrallell since the programming of the modem takes 1 min +.
We are using an...
