I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hello Nordic team,
I was wondering if it's possible to start the MCU boot from the application at runtime.
What I want is to be able to restart my product and run...
Exercise 2 doesn't seem to work for SDK v2.6.1 with v2.6.1 toolchain. SDK v2.5.1 works though. What configuration or code changes do I need to make it work for v2.6.1?
Hello,
I was curious if there was a project that uses 2 Mbps BLE to connect two nrf52840s, preferably with the ability to change which BLE channels the devices use. I...
In our custom board, check flash write and read using sample (C:\ncs\v2.6.1\zephyr\samples\subsys\nvs) but showing following response. the same build working fine in nrf7002...
This issue is for a programming environment on a macBookPro.
I finally get the system tamed and got to the point of testing the various sample apps provided. I wasted a...
1.Created a composite device for CDC and MicPhone. When the registration of mic SOF is interrupted, the device may not recognize the issue
ret = app_usbd_audio_sof_interrupt_register...
I would like to develop DTM and normal BLE stack operation in single firmware by NCS. Basically i will check a GPIO, go DTM test mode if GPIO short to High, go normal BLE...
Hi,
I'm evaluating the LE audio application to check the capability of using the Coded PHY for transmitting audio.
According to this page, LE Isochronous Channels: Configurations...
Please find below my config for handling Interrupt calls.
I've tested on another sensor dev board that the sensor I use is properly set up and is sending INT1 and INT2....
Hi everyone,
I am working with nRF52832, I am trying to implement the Zephyr Modbus client example onto it, but i keep receiving the following errors.
There is this...
Hello everyone
I'm trying to connect 2 board nRF52-DK (PCA10040) via modbus RTU using zephyr example (client and master in 2 different board).
I'm using visual studio...
I just installed the toolchain (2.6.1) and SDK (main) from scratch, and I'm not able to build the Serial LTE Modem and Asset Tracker application. I receive an error during...
Hi There,
Are the GPIO levels high impedance when the system is in off mode? Can you give information about their status? For example, one pin of the device is configured...
Hi there,
I'm on Ubuntu 22.04.2, 6.5.0-41-generic kernel.
I've been trying to setup the nRF connect toolchains & SDK through VSCode. Things seem to install fine, but when...
