We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello, the nRF5340's SAADC has a temperature dependent offset according to the product specification. The offset can be measured (I suppose it is automatically applied within...
Hello, I want ro test the channel sounding feature using the new nRF54L15-DK /PDK and I found a sample example for reflector role - "https://docs.nordicsemi.com/bundle/ncs...
Hello,
I have failed to get the I2C working on the nrf54l15dk, i have now connected it to a oscilloscope with pull ups.
i have confirmered the pull ups work, but as i...
I'm migrating an nRF52840 project from ncs 2.7.0 to ncs 2.8.0. We pass the board in to the west build command line. Our CMakeLists.txt uses the BOARD & BOARD_QUALIFIERS to...
Hi,
I am refering chapter 3 of "nRF connect SDK Fundamental" . ( Configuration files - Nordic Developer Academy )
I am refering few samples like "blinky_pwm", "peripheral_lbs...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
The scan window does not alternate properly with the BT_LE_SCAN_OPT_CODED option in the scan parameters. Specifically, the scan window does not toggle on and off every 30...
I am using NCS Connect SDK version 2.6.0
I am trying to create an array of models and found a problem with using Zephry macros in C++ projects. My main.cpp is as below ...
Hi. I want to report 2 observed bugs about board creator wizard of NCS 2.8.0.
1. When you click on "Create a new board", the first thing that you must enter is human-readable...
I am developing the LE Audio feature for nrf5340. My project is based on nrf5340_audio demo, base on NCS 2.7.0. I am not very familiar with sysbuild. In NCS2.4.0, I am able...
I'm trying to activate low power mode without success. I found samples but it appears not to work with the last NCS version. I want to get basic GPIO INPUT values at 32khz...
Hi,
1. I am testing nRF54L15 PDK PCA10156 0.8.1 Example is: ncs\v2.8.0\nrf\samples\bluetooth\direct_test_mode 2. Which pins can be used as UART TX and which pins can be...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
Trying to set up UART/UART0 for async. I cannot get the uart interrupt config to shut off.
CONFIG_UART_INTERRUPT_DRIVEN =n is set in the prj.conf
In config output...
