VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hello,
I am using the Zigbee NCP sample from the nrf Connect SDK and I would like to change the uart baudrate. How can I achieve this? I tried to find some configurations...
When I try to debug hci_pwr_ctrl in Zephyr/buletooth/sample using segger embedded studio, debug terminal don't have output of printk function, which based on nrf52840dk. ...
Hello All,
I am experiencing strange results when using the TWIM peripheral with and without using the debugger.
Setup :
Keil IDE for development and debugging ...
Hello! I use EK42423-03 and 52833-DK
Previous case
I understand plugging in the SWF connector, Will disconnecting from the PCB antenna and routing the signal to the cable...
Hi,
I have made an emitter (with nRF52833) and a receiver (with nRF52833 too) and i already succeed to receive data and print IQ data from the antenna onboard but now i...
I have tried to install nRF Connect SDK automatically. Although the installation is completed in Toolchaim Manager, the installed sdk is incomplete. After confirmation, it...
I have just bought GeeekPi nRF52840 Micro Dev Kit USB Dongle and would like to install the open boot loader. So for this I have plugged in the Dongle into an USB port on my...
I have been developing for several years with the nRF52832 and 52840 devkits. I have several of each available. One specific 52840 dk seems to have crashed code in the interface...
Hello, All:
I have a problem, when I turn on bluetooth scanning, my UART can't process the received data in time.
When I only use UART to send and receive data, it is...
Hi，
Due to customer demand, the 52810 chip must be used during development. At present, there are too few flash resources in the application layer, and the starting address...
Hello, For our project, we have a gateway which is in a mesh network with others devices. But we would like our gateway to be able to, sometime, connect to a specific device...
Hi, I have some questions regarding the nordic distance toolbox:
Can we use the distance measurement tool with 802.15.4?
if yes, how can the synchronisation be done...
We have queries regarding nPM1100 charging IC, I have mentioned our queries below, Please share your response.
1. What is the main purpose for the s hipping mode and purpose...
I transfer data by ESB between send and receive. And I want to transfer 2 bytes x 10 data that is received by ESB every T[s] to ESB receive (trigger) -> PPI->SPIM, 2 bytes...
