void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi, I am developing a device using the nRF52832 mcu. I have written my application and have interfaced with an external I2C Sensor. It works perfectly on the NRF52-DK, I get...
I am using NCS v1.9.1 with the nRF52840 and I am not able to move the MCUBoot secondary slot to SPI flash.
I have been able to communicate with the device over the SPI...
Hello,
The nrfjprog command is used for the nrf51822 / nrf52833 program.
Suddenly, nrf52833 shows the following error.
Even though family is specified, it is the same...
Hi,
I'm working on NRF52840 DK , S140 and I'm trying to send large data (around ~64KBytes) from a peripheral device. I'm using the following functions: - sd_ble_gatts_hvx...
Hi Everyone,
I'm currently testing the battery service with my development kit, nrF52dk, and I've found an error stating "The handle is invalid" when I press the "read"...
Hi,
I want to build a wireless split keyboard (Left and right parts). I want them to connect to one PC but only need to establish the connection one time. Can both part...
I am working on ble mesh with sdk17.0 and sdk5 for mesh I want to send large data vai ble mesh I followed this post https://devzone.nordicsemi.com/f/nordic-q-a/71105/sending...
Hello.
I've a ublox module with nRF52811 chip.
Is it possible to make a BLE beacon receiver with nRF52811? If yes, is there any demo application? I've searched nRF SDK...
I have been playing with an Ikea Tradfri E1812 button, a Philips Hue bulb, and zigbee2mqtt. I see that when I bind the button's OnOff output cluster to the bulb's OnOff input...
Hello,
I am looking into evaluating the nrf5340 with different functions running out of external flash, and how current draw is affected by these functions. We are looking...
Hi All,
I am working on NRF52840 and trying to optimize the BLE throughput. The current settings are:
PHY: 2M PHY
Conncetion Interval: 9.375 ~ 15 ms
GAP_DATA_LENGTH...
Hi Everyone,
I hope you all are well.
I'm using nrf Connect SDK v1.7.0 and VS code for nrf52833 chipset.
So far I've used NUS service in my code to transmit some data...
Hi, I am trying to write an "event dispatcher" so it's possible to listen to types of event and send events. You pass a function pointer and it will be called when that event...
I was gone for a bit came back did my updates and I can't program my boards threw nRF connect anymore. They just don't show up so reinstalled everything many times restarted...
I am using Zephyr development environment for BLE application development on my computer, now I need to use nrfjprog when burning in (flash), my question is whether nrfprog...
