here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/nrf_dm
I used the demo linked above to test RTT and DHCP respectively. Within two meters, I found that...
From the DF spec, we know that the connectionless AoA puts the CTE signal on the periodic synchronous adv, why, and what is the benefit. Is it possible to send CTE in extended...
Hi,
I am using nRF5340DK for development. Currently, I have two problems:
QS1: When I use fun nrfx_gpiote_out_toggle(), it reports Assert error on NRFX_ASSERT(! pin_in_use_by_te...
Hello,
I am working on integrating wireless-timer-synchronization into the HCI_RPMsg sample provided with nRF Connect SDK. My goal is to synchronize ADC sampling between...
Hi all,
I am using the kit nRF5340-DK, connecting to windows 11 pro. Already installed nRF Connect for Desktop 3.10.0 and nRF Command-Line Tool 10.15.4 (32/64 bit).
It...
Hi:
I want to include the Characteristic value in the advertising packet，for example the real time battery level，thus there is no need to establish a connection between...
Hello.
I wish to implement a DFU Client. One (USB connected) nRF52840 based device should update an other (Wireless) nRF52840 device.
As the SDK only has a DFU service...
I am planning on pairing two parts of my system using OOB pairing via a UART connection. I couldn't find many examples of pairing using a physical connection as oppose to...
Hi,
I use ble_app_uart sample code using nRF52840 in SDK15.
There is a code below in ble_stack_init().
And APP_BLE_OBSERVER_PRIO is defined as 3 at the top.
On...
Hi there,
We are currently doing current measurements on the nRF5340 DK with a Power Profiler Kit 2.
To do this, we simply use the PPK as a source meter and connect it...
Hello Nordic Semiconductor
I am developing a small application on the nRF52840 development kit where I need to transfer I2S signals in/out of the MCU. I have set up an I2S_IRQHandler...
I'm trying to send data readings an advertising packets from the nrf21540-dk board, and use the phone as an observer to record the data.
So far I've been able to send counters...
I'm sending a short data string from a NUS application. For some reason I cannot read the data as bytes, only string, even if the sent array is uint8_t.
Is there a specifier...
