Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello,
I'm trying out nRF Connect running inside VS Code and I'm running into issues debuggin my code. I followed the Nordic setup tutorial and installed the latest nRF...
On a freshly installed Windows 10 system, I've run in to a problem with the JLinkARM.dll and nRF Connect for Visual Studio Code. If I download and install the latest JLink_Windows_V756b_x86_64...
When I clicked the debug action for my app, the following error window popped up.
I followed the below steps to create the app:
1. check my default directory of...
Hello all,
I am trying to do a simple task, yet I cannot manage to make it work. My goal is to use the GPIO 1.01 (defined as Digital I/O in the Data Sheet) as an output...
Hello All,
This is from an app I had working 1 1/2 months ago - when I've tried recently to get it connected again, I haven't been successful.
The latest asset tracker...
hi!
when resetting the coordinator (zb_bdb_reset_via_local_action(0)), an error occurs, the program hangs. It looks like the "zb_address_unlock" function. The same when...
In the description of example BLE Heart Rate Collector, it says that it can indicate state BSP_INDICATE_SCANNING and state BSP_INDICATE_CONNECTED.
In the description of...
I have updated the Programmer to v2.0, and connect 52840 with JLINK to my computer, but it can't be selected in Programmer. Previous version runs normally. What can I do?...
Hello! I'm trying to use an external module with the VSC extension and I don't think that is currently supported (or easily supported.) For reference, our module works with...
Hello, I'm trying to manage connecting to my board (nRF52840-DK) which direct advertise (low prio) with peer address set to MAC address of my PC running Linux with bluez 5...
Now I have a problem, the transmitting power of NRF52810-QCAA is too low, only -2.73dBm. I tried to adjust the value of the capacitor, but the effect was not obvious. Excuse...
Hi, I tested the RGB Led (with an external RGB Led) with the nrf 5340. But I didn't find any pinout with a brief overview of all the pins and their features because the PWM...
I'm trying to setup the SAADC, I do this as much as possible without examples, so I really understand what is going on.
Setting up:
After this I try to start an ADC...
Hello DevZone,
I am trying to build a NFC driver but I am getting issues with it reinitializing every time I detect a field.
I am unable to use the T2T and T4T libraries...
