void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I connect the nRF52820 and other devices with UART and communicate with the baud rate of 38400bps.
I know that the transfer error rate is different for each baud...
I have two tasks and I want to run those tasks one after the other.
currently when I comment on one of the task, the firmware running without any error.
if run those two...
I have been unsuccessful attempting to perform an FDS write or update WITHIN the DFU Event handler... the update or write never completes (no FDS_EVT_WRITE or FDS_EVT_UPDATE...
Hi,
I am using NRF5340DK, and I want to define P0.20 as my SPI MOSI pin.
However, this pin is pre-defined by Zephyr as uart0 tx pin, in zephyr.dts:
Everytime I reset...
Hello,
Our product has two pieces of information that must be programmed during production: a shared secret key (128 bits) and a public, unique device identifier, also 128...
Hi guys:
I flashed the ble_app_uart(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart.),
When I pressed button1, there...
Dear all,
I'm trying to modify ble_central_uart (SDK16) to connect two peripherals. I've achieved the connection and been able to print receiving data via UART.
But...
Hi All,
I am NEW to Nordic Devices and I want to try to learn as much as I can.
I have bought a startup Dev Board to learn my skills with: E104-BT5032A-TB E104-BT5032A...
Hi guys.
I wonder the program run start from which section and how to enter the app when 52840 poweron? Start from SofeDevice?
I only flashed ble_app_uart and SoftDevice...
Hi all,
I'm trying to transfer my custom project pca10056 (which is to broadcast a beacon) to nRF52811 hardware and I'm facing some issues in the last stage of build.
...
HI ,
My environment:
nrf connect sdk
nrf5340 dk
segger studio ide.
could you please provide me timer example code for nrf5340 board.
Thanks & Regards,
...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
SDK: 17.0.2
IDE: SES
nRF52832 module
Hi!
I have a nRF52832 based custom board operating on battery power. I assigned a variable to the non_init section in SES and...
Hey!
I have an isp1807 test board, which uses an nrf52840 chip, and an isp1p807 programmer (ISP130603E). Currently, my code is written using the nrf52 sdk v17. When I am...
Hi, I'm using nRF9160 as host and nRF52833 as a controller with NCS 1.5.0 SDK. On nRF52833 LPUART sample runs, I have added needed configurations for extended advertising...
