Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I am using TWI on a 52832 (sdk12.2) and am having problems with reading data. The slave chip that can take up to 60uS (8 bus clock cycles) between to set up data after...
Can the Nrf Mesh android app be expanded to support multiple networks?, i took a look at the android software , it uses MVVM architecture and uses Dao's and repositories to...
Hi,
I found that s113 SDK17,did not support +8dB TX power,could you please give me some suggestions ,when using nRF52820, which SoftDevice will support +8dB Tx power?Thanks...
Good afternoon,
We are carrying out a new project with your NRF52810 beacon to create a heat map of
movement inside a room.
Our questionis, do you have any software...
Hello,
I am currently running the openthread client example provided in the NCS and I am trying to toggle the client as a sleepy end device. However, in the toggle_minimal_sleepy_end_device...
Hi
I would like to know the availability of the open sources for the following:
1. BLE Gateway for PC, Android , iOS
2. nRF Cloud open source
Can you help, How to...
The nRF52840 UART example uses pins 1.13 and 1.14 for the TX and RX pins on the Dev Kit (uart_pca10056) and has a default baud rate of 115200, but the 1.13 and 1.14 pins are...
Hi! I'm having issues with inconsistent battery readout results. I'll elaborate more below, but in general, I have multiple devices which 'sleep' most of the time, and when...
I have an issue when i am doing writing of a structure where autoprog is a struct like this :
typedef struct { uint8_t tag_tab[TAG_ID_LENGTH]; }tag;
typedef struct { uint8_t...
Installed nRFgo Studio lastest win64 verion nrfgostudiowin641212installer.msi and lastest windows 64 nRF-Command-Line-Tools_10_9_0_Installer_64.exe . But nRFgo does not work...
Hi!
I want to develop a simple program which count pulses in a digital pin in an interval of 10ms. I want to use a timer as a counter to count the pulses, also I want...
Hello Nordic Team,
We just received and test a new batch of SIMs using a nordic nRF9160. However, there is an error that doesn't allow to register these new SIMs. From LTE...
Hello,
we have a project on:
Periperal: experimental ble_app_blinky / and
Central: experimental ble_app_blinky c
We have add suplementary:
LEDBUTTON_LED4 ( BSP_BOARD_LED_3...
Hi,
I am unable to test current time service example.I followed all the steps mentioned to test CTS Example.But, below are the log messages:
Again if I try to reset...
I have an issue with my nrf9160 custom board.
I flashed successfully only 3 of 30 pieces batch. Other boards fail with "Failed to connect to target. No idcode detected"...
