I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I'm securely bonding to my nRF52840 development kit using SDK_15.3.0. It connects and works great with a 6 digit PIN code, but is it possible to make it connect with a character...
Hi, I'm setting up Visual Studio Code to work with nrf51 and I can't figure why Intellisense would mark some of the lines from the SDK as errors. I'm currently working with...
Hello,
We are trying to include the UART.h into examples\ble_peripheral\ble_app_hrs and are facing the said error even after including the file.
Can you please help with...
I try to how if boot/reset while power up the board and the LED5 is blinking but when I unpluged the cable and plug it again. The LED doesn't turn on any more. And the computer...
I am using nrf_serial in IRQ mode to communicate with an AT based device. When I reset the device using ATZ, I get NRF_SERIAL_EVENT_DRV_ERR -- likely because the pins go into...
Dear All ,
I am finally able to get my beacon app to compile and work on the nrf51822 using keil with s130 softdevice.
I tried to add service data to the advertising...
Hi,
I have a situation where I have to create 4 TWIS instances on nRF52832.
sdk_config.h only shows 2 TWIS instances.
Is it ok if I add other instances (TWIS2_ENABLED...
Hello,
I was testing output on a GPIO pin with the mesh/dimming_server example and was only able to see 1.6V when measured.
I read through the example on infocenter...
Dear All,
I thought i wrote this question but seems it did not get registered. We are using the Beacon App from sdk 12.3 with the nrf51822 chip on custom board. I have...
Hello, I'm still a beginner with mesh so excuse me, if this might be a silly question or has been answered before. I did not find a post that quite resembled my problem. ...
I'm trying to use some code from the sample files and given libraries to create my own custom program. Upon startup, this is what I get:
Here is the only function called...
I am Currently under process of evaluating various modules for implementing BLE Mesh, Had few concerns regarding the same, would be great if someone can clarify upon them...
Hello,
I have seen today that the new releases of the v1.0.0 SDK and v1.0.0 modem firmware were release for the nRF9160 DK. I have been able to update the modem firmware...
Hi,
I am trying to migrate my project developed on Mesh SDK V2.0.1 to V3.1.0. I followed all the steps you recommend but i am stuck with the configuration of my server node...
