here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Dear Nordic Team,
Thanks for supporting.
Currently i am working in Mesh network. My application is Single Client control 100 Server Individually . Same like this https...
Dear Nordic Team,
Thanks for supporting.
I am new for mesh network concept. I want to control individual device in mesh network (May be more than 10 device). I have tested...
Hi,
I have a project that has a bootloader based on the SDK15.3 secure buttonless DFU example. During pre-production testing, the need for downgrading the app came up. So...
Hi,
I just wanna start off by saying I know there a lot of similar posts to this one here on the dev zone, but my problem with them is that none of them (from what I've...
Hello,
we're just planning to deplay our first border router for bigger in-house installations and wan't to use a USB-Dongle with the nRF52840 as NCP with the Openthread...
Hi All,
We are working on zigbee protocol and wants to replace the existing setup with nRF52840 . We have some below queries need your answers on the same to go ahead on...
Hi
I'm developing an application that is pretended to run on an nrf52810-based custom board, The code is a modification of the blinky example from the SDK 15.0.0, and for...
Hello,
on my previous project i rellay enjoyed the offline documentation of the sdk (SDK14.2).
Since we are using the Thread-SDK now, I haven't found a offline documentation...
I'm using SDK 15.3.2 with SD 132. SES and the 10040 DK.
I'm not clear how NRF_LOG module and the new serial port library is support to work together.
I can easily make...
Hi Nordic!
In our design we see variations in the rev C lot we have received. We are using the VDDH REG0 regulator. Some of our ICs turn ON with no problem. And even when...
When I scan BLE device at nRF UARTv2.0 App in Android4.4, it is appar device name(Ex:Nordic_UART) and 6 byte device address(MAC address?).
I want to include mac address in...
The button is connected to ground directly ,and without external pull up resistor.
I found it consumes too much current when using internal pull up resistor,but when I use...
According to at client demo, LTE-M1 is the default mode in firmware mfw_nrf9160_0.7.0-29.
Modem work mode will be LTE-M1 after every reset even you changed to NB1.
I...
I am receiving an error when I try to update my custom characteristic in a custom service, which was all working fine until I started playing with app_timer to read battery...
