void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi, I am trying to fix a crash in the dfu service. I am using a custom board based on the NR52840, SDK 15.0 and softdevice 6.0.
I am trying to add some new characteristics...
I would like to run a SPI program that reads data from a non Nordic chip. I would like to then take the data I received over SPI and send it via BLE.
Are there any code...
I'm trying to place my device in a low power mode for shipping. I used Logging and CLI while its in operation, but I'd like a way to enable/disable the CLI+Logging over BLE...
I'm testing a simple program below, which writes three params followed by read the three params.
Each params is set in tx_buf correctly, but nvs_write does not seem to work...
I am developing a hand-arm vibration sensor for read-out via BLE
Development platform NRF51822 and S110
I'd like advice on how to configure the softdevice and the two...
Nrf52832 sdk15.2 is debugged online after burning softdevice, bootloader and bootloader settings. In the ble_dfu_buttonless_async_svci_init() function, the error NRF_ERROR_SVC_HANDLER_MISSING...
HI,
The nordic MCU I am using is NRF52832.
I am flashing the example code ble_app_uart which is coming in the directory "nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral...
Using Telia APN the following is added after bsd_init()
AT+CGDCONT=0,"IP","lpwa.telia.iot"
However, this AT command sent on the AT socket fails with "ERROR". Does the...
I have 2 client nodes and 1 server node . How can i possibly recieve packets more than i send. I sent 114 packets from 1 node and 104 from another . I am receiving 302 packets...
We are developing Beacon using NRF51822 SoC.
Basically We want to classify our beacons from other manufacturers and want to give our each beacon an unique ID. Please provide...
Hello,
I am new to nrf52832 ,
My question is how to start the timer when external interrupt was rise and turn off timer again when external interrupt was rise
Kindly...
Hello to everyone.
I'm working with Light_switch example in Mesh 3.1, with nRF52832 SDK (PCA10040). I'm trying to stablish communication from server to client, sending a...
