VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hello Nordic Team,
I am writing because I encountered an issue while developing a BLE application on the nRF5340 development board. Currently, I have set up this callback...
With multiple of the provided samples with the SDK, I'm getting a repeated build loop that ultimately fails due to a remaining "dirty build.ninja". This is primarily with...
Hi,
I am working BT840F which has nrf52840, I am using ble_app_uart example to transfer UART data to app. I wanted to know what is the system frequency of the microcontroller...
Hi,
I am using an external flash on the NRF52840DK via SPI and have established working communication with the flash memory. However, I need to disable CONFIG_SPI...
In my project, using nrf52840 controller, I am trying to store 253 bytes of data in NVM, but I encounter an error: "flash_nrf: invalid address: 0x00100ff8:8." Is there any...
Hello DevZone,
I'm porting my project from NCS 2.5.0 to NCS 2.7.0.
I know that there are lots of changes in build system, especially in Zephyr sysbuild. So, I decided...
Hello, I was able to update nRF Connect SDK to v2.7.0 fine using nRF Connect for Desktop. However, the nRF Connect for VS Code extension update v2024.7.13 causes VS Code launch...
Hi,
As described in the subject I'm not able to set "Extra High Drive" for a GPIO. This setting is described in 7.13.5.11 in product specification version 1.3. I'm able...
Setup:
nrf52840DK (Zigbee Cordinator based on Zigbee Coordinator sample)
nrf52840DK (ZR)
NCS v2.4.1
Hi,
I have encountered dangerous problem during development...
Hi, I received out nRF9161 DK a couple of days ago...
To reduce the number of possible failure points, I registered on ONOMONDO with the SIM provided together with the DK...
Hi
1. Can nRF52832 meet both 2 and 3 functional requirements? 2. nRF52832 of the smart lock is connected to the Bluetooth of the mobile phone to unlock. 3. The nRF52832...
Hi,
We are developing a mesh network. Our requirement is the one device can connect to three other devices. Using one connection as a peripheral and up to two connections...
Hello,
I'm working on a driver for the PCF85063A RTC in SDK 17 with the nRF52DK. I am able to successfully set registers, however I'm getting strange behavior with reads...
I am able to open up the Cellular Monitor and successrully select the device an get a connection. However the option to ' Open a Serial Terminal' is greyed out, and so not...