Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
i try to get HRM example to work with eclipse. I can compile the project with GCC in eclipse and flash it to the PCA10001 eval board. I can find the HRM with the...
Does anyone have additional information on the relationship between SAMPLEPER and REPORTPER in the nRF QDEC?
I understand that the SAMPLEPER sets the base sample period...
Dear all :
I was recently reading ble_app_hrs example code , the PC1001 Board dowloaded this code can connect with other devices and they can send data from PC1001 to other...
Hi,
is it possible to handle a 2 second button press and wake up the device with the app button modul?
Or should i handle the button without the app button modul to wake...
Hi,
Last time I met "nRF51822 DK Setup Wizard ended prematurely". The problem was solved by installing .NET framework 3.5 on my PC. Now the same problem is come up "nRFgo...
Now i know the Cortex M0 does not have a floating point unit. Does this mean that we cannot do floating point calculations in our application? or is there a library that will...
Development environment : keil mdk 4.7, nRF51822, SoftDevice 6.0-alpha, nRF51 SDK 4.3
Hello
I develop the application with RF and BLE by receiving UART msg. So, my program...
Section 8.1.2 of the nRF51822 Product Specification states that the "Standby current for 16 MHz crystal oscillator" is 35 uA. The footnote says that the current is drawn ...
Hi,
I met this prompt(see attachements) when I install nRF51 SDK. Who can tell me what's mistake it likes? I have installed microsoft .NET framework 3.5 before in my winXP...
Hi,
i programmed the softdevice with nrfgoStudio but i get an error and i can't load the softdevice on the chip again.
The Error means that the cpu is not halted and that...
Hi guys,
I hope you can answer my question:
I made myself a custom pcb for testing purpose. I can program the nRF51822 just fine. Thats the actual state right now.
...
I have a nRF51822 dev kit, and my dongle is running the master emulator firmware, and master control panel is running on my computer, the dongle is connected and started discovery...
Dear Nordic, could you please comment on your plans to release an over the air bootloader for nRF51822? What is the approximate time frame that we can expect that? Is there...
