Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
I am trying to format an external flash chip with littlefs, but keep getting an MPU fault. I can erase the chip, but not mount or format. I have tried writing and reading...
I'd like my VS Code build configuration for my project to be included in version control.
It seems like this configuration is stored somewhere in the "build" directory that...
Description:
I encountered an issue where my NRF54L15DK development board fails to connect to my Windows 11 PC. Upon plugging in the board, the LED near the debugger starts...
Performing a DFU with an iPhone works in some configurations and fails in other. Android consistently works.
The failing version of iOS is:
iPhone 12 mini
iPhone 13...
I'm trying to connect a SIM800L to my nrf52840-dk which I power through 5V USB. I'm a beginner at electronics so just want to make sure I understand how to wire things, please...
Hi,
I would like to know what are the prerequisites to get the ICCID of the sim card:
This is the code I use, nothing special. I can get the IMEI of the modem but not...
Hello,
In nRF5340 I use one RTC and it works. Here is my code:
1) in prj.conf:
CONFIG_NRFX_RTC=y CONFIG_NRFX_RTC0=y
2) in the code:
a) define: nrfx_rtc_t sti_period_rtc_0...
Good morning,
I am using the nRF9160 as an AT command modem running the SLM app. I aim to set eDRX and disable PSM (PSM doesn´t make sense in our project). According to...
Hi all,
My team and I are evaluating some BLE modules available on the market. One of them is the UBLOX BMD-340, which contains the nRF52840-QIAA SoC.
We are encountering...
Hello Nordic Engineer,
I have already implemented a Mesh network using iOS nRF Mesh, 5340 DK, and 52840 DK, with the mesh_light example.
The NUS I used before was able...
I am trying to flash the Enhanced ShockBurst (ESB) example on an nRF52840 USB Dongle (PCA10059) . Since the ESB example is originally designed for the PCA10056 (nRF52840 DK...
Hi all, need to establish a CIS connection to an already connected BLE device with security level > = 2 . However when the ACL connection has security level > = 2 and the...
Hello, We're developing a project on a custom board based on nRF52832 and noticed that P0.20 is high on powerup, even with no firmware. Is there a way to controll the pin...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
