Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Backround: We are planning to use TF-M with a two-stage bootloader (NSIB & MCUBoot) using dual-slots for secure and non-secure images. We need to support configurable fixed...
Hello Devzone,
In our product we are working with a nRF52840 microcontroller and periodically transmitting large sums of data to a PC or a phone.
We noticed that over...
Hi All,
I have designed my custom pcb board for nrf52811. With the Jlink the IC is detected in visual studio code also it gets programmed. But i did not see its working...
Hello,
I am currently working on a project that involves interfacing the TLV493D 3D magnetic sensor with the nRF52832 microcontroller. I would appreciate any guidance or...
Hi
We use the nRF52832 for an NFC device. The device is 99.9 % in the system off state to save power as much as possible. because the device is power by a button cell battery...
Hi
I'am using nRF util version 6.1.7 for a long time to generate a DFU packages. I need to debug my ble data so i thought of using ble sniffer from nrf util. But the ble...
Hello! We have a project under nRF Connect SDK and Zephyr. It uses Bluetooth central and peripheral role (GATT client and server).
The project works good under SDK v2.7...
Hi,
I'm trying to connect to the nRF52840 dongle using nRF Connect for Desktop Programmer v4.5 on MacOS 15.2 so I can update the firmware. The dongle has the red flashing...
I've then tried both the command " nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded" as well as "nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded --scan-follow-aux...
Helo,
I lost the PUK to my iBasis SIM, so I can't register it on nrfCloud.com for my 9160. Is there a way to recover it or do I need to buy a new one? (If so, where?)...
I tried to write the following simple '.overlay' file:
However, I am getting the following error:
but if you look inside the .dts files provided by the 'nrf52dk' I...
Hi everyone,
I’m working on a Zigbee application using the nRF52840, and I’ve been experiencing periodic reboots that I cannot figure out how to resolve. I’ve already updated...
Hello. I have a question about the development environment when developing using nrf.
When you build a new board and make firmware without using dk or ek, do you usually...
