During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in "nRF5_SDK_15.3.0_59ac345" as following:
A custom board...
let say i have a temperature sensor connected to one nrf 52840 dongle of a mesh network. Now can i make the Led of all the dongles glow if the temperature increases the given...
I downloaded the latest nRF5_SDK_15.3.0_59ac345 and some other old versions of SDK documents. (I am trying to use pca10040 development kit to program Fanstel EV-BT840F, aka...
Hi
One of our customers have complained, that our sensors are making occasional errors.
I have looked at it, and they are correct. About 1 in 8 Million packets send...
Hi, I have my custom board for the nrf9160 ,
I was able to program it through the built in programmer of the nrf9160 dk but I have an issue, when I connect the VDD to the...
I'm using adafruit_tag_reader example to read ISO14443 tag. When I put a tag near scanning area of PN532. It reads tag multiple times till I remove that tag from there.
...
Hi!
I am using IAR compiler for my project
I declare global variable
__no_init u32 uPowernResetSignature;
in my code I assign value to this variable
uPowernResetSignature...
Thank you for taking time to look at my problem!
I have managed to combine the TDK/Invensense library for their IMU MPU9250 within the SDK 15 utilizing simple TWI calls...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi, I am trying to modify UICR PSELRESET but its not changing. Any help?
NRF_UICR->PSELRESET[0] = 0xFFFFFFFF ; NRF_UICR->PSELRESET[1] = 0xFFFFFFFF ;
Thanks
Hi,
I'm developing an application using the timeslot API for a custom radio protocol. The application also uses a number of the nRF52832 peripherals, as well as the app_scheduler...
Hello,
I'm having an issue with scripting AT comands directly into the code of the nRF9160. I'm a novice at all this so I apologise if the mistake is an obvious one.
Inside...
I get "ERROR: There is no debugger connected to the PC with the given serial number." when I run e.g. nrfjprog --eraseall on command line.
Programming/debugging using VisualGDB...
Hi,
The User Guide v1.3 in Chapter 2 (minimum requirements) states "SEGGER J-Link Software" under "Software requirements". Is there J-Link software specifically for use...
I've been developing firmware for the nrf52840 for a few months using armgcc+openocd+arm-none-eabi-gcc working successfully. I recently upgraded my ubuntu version (18.04)...
