Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
USB Virtual COM
Until now, the development has been done by sending the commands via a USB virtual COM. The received buffer of int is processed and sent to the function...
I have an nrf52832 connected to a UART-USB driver with RTS/CTS. CLI manages the UART connection. Using SDK 14.0.
When HWFC is enabled, if a serial connection is NOT established...
Hi, p0.06 is always high lever when the following codes are executed:
nrf_gpio_cfg_output(6); nrf_gpio_pin_clear(6);
Why?
Softdevice is used in the project.
I have searched through the examples and the documentation (BTW the online document links are broken - the offline documentation is nice however).
From what I can tell...
Hello Everyone.
I am doing a project where I need to do a Bluetooth communication of data. I have two nRF51 DK so the idea is to connect a particular pressure sensor to...
I am trying to create a state machine that will be able to turn the Bluetooth radio on/off and possibly change the mode of the BLE service for power testing. I hope to run...
I have created an instance of time using the standard time function in C. I have also linked it to a counter on a timer so I can track how long the device has been active...
At CES this year (2018) there was a booth showing essentially a roughly 1/4 size Thingy:52. It wasn't actually at the Nordic booth so I'm not sure if it was actually a Nordic...
I think there's a problem with the beacon advertisement sent by Thingy52. I'm seeing the problem in my own PC code and also air sniffer. The advertising data packet looks...
I am using nrf_fstorage_read command to read data from flash. I have defined my start address as 0x68000 and end address as 0x72000.
I erase the memory through nRFgo studio...
Hello,
I've searched around the forum and followed all the advice given in other threads but am still not having any luck.
I've tried running the nRF sniffer on both a...
Hi there. I just got the nRF52840 DK and am trying to get going with it. I have been looking at this getting started page:
https://www.nordicsemi.com/eng/Products/Getting...
Dear lovely people!
Setup: sdk14 / s132 v5 / nrf52832
Just like with the previous SDKs, I tried to make a multilink nus central fw.
The periph device runs my code based...
Hello,
In our application we heavily use the application scheduler. This was done for 2 main reasons:
serialize access to system resources
enable the soft device to...
Good Afternoon,
I'm writing some config data on an empty record the first time I turn on my board and updating that same record every next time I turn on the board.
...
