I had to modify the modem_cellular.c file driver in Zephyr to make it work for a SIMCOM modem. I know I could try getting a PR to Zephyr approved but it'll take some time...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
NRF52840DK NCS 2.8.0 Hello , We are developing an application where a device with router function must join a coordinator network. The coordinator uses OOB (proprietary IR...
Hello!
I need to use download_client to get files from an HTTPS server. I'm stuck in the implementation process - I'm lost when it comes to TLS etc. I tried to extract some...
Hi everyone,
After the latest update of the nRF Connect SDK plugin for VS Code (2025.4.106), we've seen this pop-up appear. We are using v1.8.0 and now we are not able to...
1. Set up the development environment for the nRF52840 chip in VS Code, but encountered an issue where the chip could not be recognized. The development environment consists...
I'm using SDK version 2.9.0 with an nRF52840 in a combined peripheral / central application.
The nRF52840 device starts advertising, but then after connecting (as a peripheral...
Hi,
I am trying to download the nrf connect toolchain in vs code but getting this error
Error: Failed with exit code 1. Failed to download toolchain bundle Caused by...
Hello.
I am developing an application based on IOS-nRF-Mesh-Library, and currently considering porting firmware upgrade function of IOS-nRF-Connect-Device-Manager for updating...
Dear All:
I don't have a le audio enabled phone, and i want to study the hci commands about cis and bis setup up processure.
Could you please provide some HCI logs from...
Hello there!
I'm trying to run the official, unmodified, version of the `WiFi Shell` sample targeting the `nrf7002dk/nrf5340/cpuapp` board and am currently getting:
...
Dear,
I recently upgraded my project from NCS 2.4.0 to NCS 2.9.0 and encountered an issue with the ST7789V display driver.
Previously, I used SPI0 to interface with the...
Hello, my application is running on a custom board. The BLE Host is on an nRF9160, the BLE Controller is on an nRF52820, and the SoCs are connected via UART. On my original...
Hello,
I am new to multicore programming. I tried to find without much success a complete VS Code sample project from Nordic targeting nrf5340 two cores; ideally with the...
I am attempting to connect my nrf52840/52811 DK to my custom PCB that contains nrf52840. The DK users guide describe the connections on the P19 debug out port but I can see...
Hi all,
This is for nrf9160 with firmware version 1.3.1.
I 'm trying to read back the certificates and comparing with a known CRC.
modem_key_mgmt_read is able to read...
Our system is composed of a nrf5340, a QSPI flash, and a nrf7002 on single wire SPI. We are not using the network processor.
We are using Zephyr NCS 2.9 with sysbuild. We...
I am testing the Sleep idle current for the nRF52833QDAA module.
The module is nothing connected outside except the fundamental circuit as the attached picture shown.
...
Hello,
We have the nRF52833 included in a new PCB design. So far it works well using mcuboot and a UART interface.
I'm trying to get the radio set up and running, and...
NCS: v2.7.0 nRFCloud/utils: a2db3ffedbda237f9c1efb7a68ec2d270c346e56 Hardware: Custom Board with nRF9161 I am writing a provisioning automation (with robotframework), but...
Hi,
I am using sensor observer sample to get the data from sensor sample. However, I notice the power consuption is too high. I have look thourgh the forum and found this...
