Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
using the sample code at
invent.module143.com/.../
i am able to use nrf24l01 to communicate raspberry pi with arduino, but the problem is the timing. I found it takes...
Did anyone attempt time of flight measurements with the nrf52 yet? I'm looking into this as a possibility to measure distances. I was thinking that using the 64 MHz clock...
I AM GENERATING A PWM EXTERNALLY (OUTPUT FROM A WATER SENSOR) AND FEED IT TO A NRF51422 BOARD. I WANT TO COUNT THE PULSE COUNT(LOW TO HIGH TRANSITIONS ONLY). CAN I DO IT WITH...
How to configure an app_timer in counter mode. i just want to count number of pulses in pwm using app_timer. i didnt find any example in which app_timer used in counter m...
I'm trying to use fstorage module for event logging; several pages are used as a large circular buffer. When logging wraps from one page to another, the new page needs to...
Hello every!
I was developed my aplication base on nrf52 SDK (version 14.0). I am confused about SDK_config.h file. I can't cognize which macro should be 0 or 1. Example...
Hi all,
we are using the Nordic Uart Service in our product and Id like to connect our hardware to a Linux powered PC. Does anyone know how much effort it would be to make...
Hi all,
I have a working ADC implementation (S130 + Application) and use it to measure an analog input continuously.
However if I use the same code on top of bootloader...
When I have a test using nRF24l01+ with STM32, I can only get a playload datarate no more than 450kbps using nRF24l01+ 2M mode.
How can increase the playload data rate and...
I have been using two NRF24L01 to communicate with each other using just simple Arduino Uno Board.
it worked for 5 days and now all of a sudden it is now working.
I tried...
Hi,
in order to add flash programming support to the iSYSTEM toolchain based on a
customer request I would need a flash reference driver/monitor implementation.
Would...
The sync time for my nrf2460 seems to be about 4 seconds. Is this normal? Secondly, once
the pair is synced at close distance, one or two feet, as I move away sync is lost...
I'm planning on having all of the different Device Information Service characteristics (fw_revision, sw_revision etc) with each being just a single integer for version number...
Can someone tell me what these errors actually mean
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -1.
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -102.
...
