Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
Hi guys!
I wanted to ask that can we use an external flash(connected via SPI/I2C interface to the mcu) instead of internal flash for storing downloaded image(s)?...
Background: We use NRF52 chip along with SDK 12.1.0. Since we have a few components of firmware (i.e. secure DFU settings, secure DFU , application, Softdevice) that go into...
The aim is to use the nRF51822 chip beside the application processor and to run the soft device S130 in it but as I saw, the newest SDK v12 supports only S132 Connectivity...
I am trying to update my S132v2.0.1 devices over the air to S132v3.0.0 and am getting no bootup, even after swapping dfu_dual_bank.c from the answer below.
devzone.nordicsemi...
I am studying this tutorial: nRF52 Online Power Profiler . I know this tutorial basically related to the ble_app_pwr_profiling example in the SDK: Power Profiling Application...
Hi, Nordic
I know pipe0 and pipe1 are be enabled on nRF24LU1 nRFgo SDK example for default PRX.
Now I only to enable pipe0, disable pipe1.
First, I use this...
Hi, Nordic engineer
nRF52832 as ESB PTX, nRF24LU1 as ESB PRX
same channel, crc, and match address and pipes, but from nRF52832 uart log, ESB TX fail event always show...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hello everyone~
Although one TWIM interface of the nRF52832 can "interconnect up to 127 individually addressable devices", I still think that use different interface will...
Hello everybody.
I'm trying to modify the original firmware that comes with the nRF51822 to make it sweep all of the permitted levels of transmission power.
I was able...
Hello,
I want to read the temperature value continuously on mobile scanner app. I implemented the program as stated in BLE Characteristics beginner tutorial and I am using...
Hey guys,
I’m trying to come up with a way to know if an advertisement was received via BLE_GAP_EVT_SCAN_REQ_REPORT, but then not actually send the SCAN response. It’s...
Iam using softdivice 110 and sdk 10.0.0, iam using spi driver for interfacing with spi slave device(flash memory device). I need to send command and then receive the data...
Hi,
I am trying to implement an ECG measurement device. nRF52832 collects the sensor value through SPI and send it to smartphone using ble_app_uart code. I need to send...
