Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
I am trying to use an ESP8266 ( ESP-01) to add Wifi capabilities to a nRF9160 project board. I am using nRF Connect SDK V2.9.0 and the V2.9.0 Toolchain.
To set it up I followed...
I’m trying to implement DFU upgrade of NRF5340, I can send the image (./build_5340_app/build/signed_by_mcuboot_and_b0_s1_image.bin) to the device when running and it seems...
We are trying to add CarbonDioxideConcentration cluster in matter. we are able to add temperature and humidity clusters and values which are updated are getting read in chip...
Hi,nordic team
Iam programming with nrf52833 and ncs v2.9.0
I am doing DFU by myself.And I Flash_write data into slot1_partition,I am sure my data write in flash is correct...
Hi all,
We are running v2.4.0 SLM in nRF-9160 as pure modem, communicating with our external MCU. And we need to send a MODBUS-TCP write request command about each 10 seconds...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
Hello,
I migrated from SDK 9 to 11 (S132) and i cannot receive anymore custom advertising (from another nRF52)
I receive another devices advertising events so reception...
I'm looking to use this dk for a small project.
Has anyone made or seen a box for the devkit easliy available (.STL) for 3d printing?
And for added coverage, can I just...
The documentation for EVTEN in the manual, showing the RTC Tasks and Events system (Figure 45) led me to believe that if EVTEN for an event is disabled the EVENT will never...
Phone Model: model MX4 from MeiZu china
APP applied: nRF Master
experiment 1:
Here in my hand, when a android phone try to connect to the device which contain the service...
I just now saw the press release for the Primo .
In theory the bootloader should just to be able to be loaded to an existing DevKit either via NRFstudio or the NRFprog...
www.youtube.com/watch
Hi,
I'm a beginner in Iot. I found this interesting video and observed that NRF51 SDK and NRF Beacon communicate with each other. I want to send...
I have12 input pins to my application. But the code fails when I try to add the fifth button.
Is there a limit to how many input signals I can add?
static void gpio_inputs_init...
Hi,
I am using SDK 11 and S130 for my ble application. S130 acquires 108k of flash memory. How can I reduce it to less than 100k or should i use S110 since it uses just...
I have OCD for compiler warnings... I must use -Wall (I'm a freak like that).
In nrf_drv_twi.c line 433 there is a function twi_clear_bus. This gives an -Wunused-parameter...
Hello,
I was working on a nRF51422 and made a project using the example ble_app_uart_c. It works fine on the DK, but now I want to make it work on a board that has one...
Hello,
Does anyone know if the information and methods given in the links below are still valid for nRF52?
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../ ...
Hey,
We're are newbies with Nordic and are trying to program BLE HRS example code to run straight on the nRF52832 (instead of the PCA10040 target).
In order to do so we...
Hi everybody! I am here again bothering you with probably silly questions. I have, on my smart beacon kit, an application that uses an ADC and then sends the converted value;...
`Hi Guys,
My project requirement is that first time i have to bond and connect my nRF8001 BLE with peer device, once connected i have to find peer device address, after finding...
Hi everyone,
I was not able to find a full example in the SDK or online on initializing ANT to work with burst mode. Also, I was wondering if it's possible to setup ANT...