Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
hi i have a question
i ues ncs 2.9.0
This is the code that displays my Bluetooth connection
——————————————————————————————————————————————————
struct bt_data ad[]...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hello, I've recently upgraded my pre-production application on nrf52832 from NCS v2.6.2 to Ncs v3.0.1 also upgraded to HWv2(on interim ncs 2.9.0 as adding custom board for...
Hi All
I am aware that there are some changes to UV5.12 to do with Device Pack location etc.
I have currently updated my project from the .uvproj to .uvprojx extention...
I was able to setup gazell communication between two devices one as device and other as host using 32 byte payload size in nRf51822 module.
Here in gazell communication is...
We are using the Nordic Semi nRF51822-QFAC on our device for BLE. Since we are developing from scratch I understand we need have FCC testing done. Is there a summary of the...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I had a nRF81522 design that was working at 3.3V and I dropped the voltage to 1.9V. I didn't change anything else, but now I am getting periodic disconnects during interogation...
I have a PCA 10028.
This board uses Two microcomputers.
One is N51422.
Another is microcomputer on which the seal is put(Segger ID:).
What is the role of this microcomputer...
I recently discovered this article ( mbientlab.com/.../) and am trying to understand the data transfer type between the firmware ( ble_app_hrs_s110_pca10028 ) and an iOS device...
Hi,
Currently when I run the HRM demo I end up in the app error handler, unfortunately the error codes don't print to my terminal window. I'm using crossworks, and I was...
Hi,
I am new to using keil uvision. I am creating wearable solution, have enabled battery service indication, RTX support,bsp support, gpio,ble service.
When compiling...
Hello!
I would like to measure RSSI for different channels so as to decide which channel is the least noisy one (and more particularly, which ones are already used). I...
I am trying to choose a BLE device for my upcoming biomedical product design. Any help in comparing these 2 devices will be greatly appreciated.
Things I am concerned about...
Hi,
I am using the nRF51822 with an external chip. The nRF51822 has interrupts which trigger when one of the signals from the external chip goes low. When using BLE and...
My program does a lot of dynamic memory allocation and at some point "malloc" retruns NULL , which is cause the system running out of allocated heap memory (I am assuming...
