I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Good morning,
I am trying to figure out how to write unit-tests using NRF Connect and Zephyr on Windows. Therefore I am trying to use unity as described here:
http:...
I have developed a custom board using nrf52840 IC and I need to use UART. For this I have two pins available P0.19 and P0.20 to be configured as RX and TX. I checked those...
I am using a BC840 on custom PCB for a low power data logging application and am struggling to get lower than 270uA sleep current. This part has the 32mHz external crystal...
Hi,
The python nrfutil package doesn't seem to be actively maintained.
Latest updates don't support python version > 3.9 which are now default versions for latest Linux...
Hi,
I downloaded the project for PCA10040 with HID Mouse in ...\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs . From Iphone and computer, I could...
Hello,
in my project i want to use watch dog timer in ble_app_uart_pca10040_s132 but am getting error as shown in image1, even after including driver files and paths
...
hello,
I'm trying to use RSSI Viewer for my custom board - problem is I need to change UART pin.
How do I make my own FW/binary for RSSI viewer?
My custom board uses...
Hello,
I'm very unexperienced with low-level programming, so I apologize is some of my questions make little sense.
We have this board that sends telemetry data using...
Dear Support,
I updated the nRF Connect for Desktop's Programmer to v3.0.0 and noticed that it is no longer possible to write a file to a nRF9160 using a Segger jLink without...
I am currently programming an evaluation board to get to know BLE better. Currently I am using the nrf52811 on a custom board.
So far I used an example from nordic to create...
Probably there is already some solution here in the forum, but I couldnt find a fitting one.
My problem: I have custom code on my nRF52840 DK, which is used as an aggregator...
Hi,
I am running a multirole device based on the 'central_and_peripheral_hr' samples of nRF Connect SDK v1.8.0. The device holds a connection as peripheral and it is scanning...
Hi Sir/Miss,
I use nRF52832, softdevice 132 and SDK 17.1.0 to develop.
And, I want to use GPIO to wake up from system off.
We use external pull up resistor in wake up...
