I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello,
I have been building an application using the CLI and I am thankful for the CLI example and how well it works. I am wondering is it possible to use the CLI but...
Hello, Im using SMP over UDP (OpenThread) and after updating to v1.6.0 in NCS, sending most commands with `mcumgr-cli` makes the device restart with:
This happens for most...
We are currently experiencing malfunction with the big chip on nRF9160dk board, which provides USB-UART and jLink functionality. After 30 minutes, to a few hours, we either...
I have nrf52832 dk. I used power down example by github
https://github.com/NordicPlayground/nrf51-powerdown-examples : system off wakeup on gpio. Upon current measuement...
Hi Nordic Engineers,
I have few queries over HFCLK 16 MHz timer.
I am using nrf52840 custom board. IDE - segger embedded studio
I have enabled HFCLK timer and able...
I'm using nRF52840 and want to send a data of 200 bytes over BLE, but while adding the characteristic, if I give maximum length above 101 it does not accept it. Can someone...
I am working on a limited release project that has multiple devices which require programming. Part of the appeal of this device is its programmability so I am going to provide...
Hello,
I am looking for a low latency (end to end) wireless module for Joystick application and this is for a medical VR platform.
Latency requirement is <= 5ms.
Data...
Hi I'm new on zephyr
In my hardware the sensors around the soc are most of time not powered.
At Startup the OS initialise SPI, I2C, UART and some pins are set to 1....
Hi,
I am working on nrf52832, s132, SDK17, trying to trigger the saadc with the RTC2
This is my setup :
what I am trying to do is to periodically trigger a series...
I am using a custom board using the nRF52832. I have developed a number of applications using this board sucessfully using nRF5 SDK.,
I am porting a current application...
Project Zip:
Following is my setup:
Board : NRF52832 by Sparkfun( Link ) - Added pull-up resistor for TWI
Sensor: LIS2DH12(Custom breakout)
IDE: Segger Studio...
https://devzone.nordicsemi.com/f/nordic-q-a/79832/need-interface-mcu-initial-boot-firmware
apparently i can't update it anymore. does 'engineer assigned' mean that it can...
