I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
I have a requirement to start the MCU with extended non connectable advertisement for few minutes and then activate normal connectable advertisement for another few minutes...
Hello,
We have an app_timer that runs periodically for the application, and we are also using BLE peripheral code. Once the application timer expires, the event handler...
Hi,
The Dongle was given to me by a colleague of mine who has the exact same laptop as I do. The Dongle was and is working fine with his laptop. The problem is with my office...
Hi ,
i am using nrf52832 soc with customize board trying to optimize the power the following events occur:
1)The first time when i code uploaded it initialize all the...
Hi,
Is there a way to set somewhere in the softdevice or a library to automatically disconnect after an idle connection? Idle means, nog characteristics being read or written...
Dear Nordic,
I have some questions when study the usb audio of nRF52840;
What function when running the nrf_drv_usbd_errata_104 function?
Do I have run it? Can I remove...
Hi,
I am struggling to find a basic sample for UART communication in NCS. As an experienced Nrf5 SDK programmer, I find it very hard to convert my firmware to nRF Connect...
Hi Nordic Support
I have been experimenting with your nRF52840 board there has an SPI flash and have tested it with your USB example that can enumerate the filesystem on...
Hello,
I have the following setup:
a computer connected to a PCA10040 over USB
a PCA10040 connected to a NRF52832 over SWO (SWD IO, SWD CLK, SWO, RESET).
I would...
1. I am using the nrf52832 at the transmission side (ble).
2. at the scanner side I am using the ESP32.
3. I want to display the "advertising device name: " at ESP32 side...
Hi ,
I have been tryiing out the flash_storage example in the SDK /examples/pheripherals/flash_storage . The flash storage , permits us to write hello world to any memory...
Hi There,
I am developing Mesh applications based on Mesh5.0. At present, I have nrd52850DK broads, how can I do to debugger the application? Do I if have a J-link device...
I am not getting how to implement below two points in installation of micro-ecc
Enter the subdirectory for the SoC and the toolchain that you are using to build your application...
Hi Nordric,
In our application we want to receive the sensor data using SPI-DMA and to send processed data on USB.
1. Is it possible to receive sensor data and directly...
Hello,
When I set the tx power in the broadcast initialization, I found that there are restrictions on the setting of the Bluetooth name, as follows
My device name:...
