Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I am using sniffer v3.1. I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC with windows 8.1 it appears as "nRF Sniffer for...
Hello,
In our product, the nRF9160 is configured to use LTE CAT-M1 and we are measuring the signal quality thorugh the AT+CESQ command.
After begin registered on the...
Hi: I have write a spi slave, and write a spi master on STM32, It can receive data from STM32,But I have no time to prepare the response data.
as the code below, I can receive...
I checked the SPI communication using the NRF52832 development board.
Based on the firmware of the previously developed NRF52810 product, the SPI operation code is applied...
Would like to interface a SPI ADC – MCP3461 via the nRF52840 serial peripheral interface master with EasyDMA (SPIM). I was not able to find whether or not there is an available...
Hi Everyone,
My issue is mostly stated in the subject, I hope someone can help me recover this DK because as of the moment this is my only way to program/debug out EVT board...
I have nrf52833 as Tx. Ialso have nrf52833+ antenna array as Rx. I want to send CTE data, implement IQ sampling and view AOA for implementing direction finding. Kindly assist...
Hi,
I'm considering shifting to SES (from VS-code) to get debug capabilities.
(Zephyr application developed under NCS tag v1.5.1)
I tried to import my project doing...
Hi
I am developing a Zephyr application on a nRF52840.
Is it possible to runtime change pinmux. Eg. I have set rx/tx for an uart to p1.8, p1.9 and want them to be changed...
Hi nordic,
I want dfu the BL only, how should I pack file? Can show me how to pack instructions of nRF Util, only update bootloader.
Thanks and best regards!
John
Hello,
I am using nrf51822 / SDK v12.3 / SD 130.
I want to change the FW of the sold product to a new FW.
The bootloader address / length of the two are the same,...
Hi! I'm working with an nRF52840 SOC using SDK 17 and Keil. When I try to allocate memory to a structure of size 8388 bytes, malloc always returns 0. I've set __HEAP_SIZE...
