I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello,
I have been trying for days to program my nrf51422 project without much success. I am using a Jlink programmer. I have connected VTREF, GND, SWCLK and SWDIO from...
Hi,
I know that this question has been asked before but I was wondering if someone can help me understand if the problem is from the connections on my board or my chip...
I am developing a fairly complex app which involved having a lot of logging using the NRF_LOG macros with the UART backend. I am using the nRF52 DK as my platform with nRF...
My app is based on ble_app_hrs_rscs_relay, i.e. the nRF52 DK is acting as central and peripheral at the same time.
SDK 17.0.2, SD S132 v7.
I have a service running there...
Hello, Can your tell me is it possible make three from one device at the same time ? If is not, can I make multiple connection with profiles which support multiple connection...
My goal is to synchronize the clocks of several nodes in a mesh network. I would like the client node to distribute the current time to all the server nodes in the network...
I am trying to run nRF9160: Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) on thingy91. I have followed Azure IoT Hub — nRF Connect SDK 1.6.99 documentation...
Hi,
I am looking at the product brief for nRF21540 and found "nRF21540 Development Kit" and "nRF21540 Evaluation Kit".
Where can I get the H/W information for them,...
Hi,
We want to implement a smart energy meter by using a mesh network including 200 nodes (nrf52840). What is your suggested protocol to do this?
Thank you in advance...
Hi! We're working on a BLE product which is intended for use in the US. This product uses an nRF52833 SOC, with some external components on a PCB we've designed with a printed...
I'm trying to evaluate a Nordic BLE module for a new battery powered project while waiting to establish a connection to a base station device. It seems like your lowest powered...
Hello,
When we tried to increase the Security level from SEC_OPEN to SEC_SIGNED_MITM, it will output error 0x6 which is "Not supported". So how can I do to support a higher...
We are developing AoA direction finding with nrf52833 and antenna array. We also want to include Wifi connectivity to our receiver, having nrf52833 + antenna array. Which...
Hello,
I want to perform NRF52840 Firmware update remotely. I refer to link .
I want only normal http OTA update without encryption for prototype testing. Is there any...
Hi, I've been measuring a nRF52840-powered prototype powered from a 3V coin cell battery. I would like to use High Voltage Mode with REG0 in DC/DC-mode for maximum battery...
