Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi, im trying to gather accelerometer data from Mi Band 3.
I found script, written in python, that allows computer with linux to connect to band. But its missing functionality...
hello all,
I am referring ble_app_hts code for development. and I need to add saadc code in my project.
app_timer is used in ble_app_hts code & nrf_drv_timer is used...
Hi,
I have one custom board based on imx6ull, which has nrf52840 embedded on it. Both communicates over serial/UART.
On host side I'm using linux Bluez stack v5.50 and...
Hi,
I am new to BLE Mesh development using Nordic.
I am trying to write a python script for mesh provisioning an configuration using Serial Interface.
when I am launching...
Hi all,
I am working on a project with an Adafruit ItsyBitsy that uses and nRF52840 chip, and I am having a bit of trouble with getting the timers to work accurately....
I currently have a device running on sdk15 with a softdevice 6.0.0. I got a bootloader running the DFU code, and updating the main image works perfect. We load a default image...
We have a custom BLE service with several Gatt characteristics using the nrf52832 SDK 15. On occasion a device is no longer able to connect to IOS devices. This occurs after...
Hello all,
we faced a problem discovering a specific service while using SDK from (12 to 16) and devices (nRF52,nRF51)
the problem is that the peripheral responses with...
HI,
we created an application on SDK "nRF5_SDK_17.0.0_9d13099" .The example code used to develop the application is "ble_app_hids_mouse".
we developed the application...
Dear all,
I have a critical problem about mesh network.
After running 2 days, some device in mesh network cannot publish message with error 15 ( forbidden ).
I tried...
We see an increased power consumption at around 26uA when enabling GPIOTE IN events in our application with a NRF52840_xxAA_REV1 chip. We use nRF5_SDK_15.2.0_9412b96 and the...
Hello,
I would like to use the NRFsniffer firmware on a Sparkfun NRF52832 Breakout board and I cannot use the UART pins expected by the NRFsniffer since one of them is mapped...
Hi everyone,
I am a new developer and I am using the nRF52840 with SDK16 and s140 for prototyping and I have some questions about the bootloader and the softdevice.
Regarding...
Hi Nordic,
I am using simple LED blinky project on nRF52840, referenced from here.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/boards/arm/nrf52840dk_nrf52840...
I ran into a problem that some parameters that I change in the device tree are not applied.
For example: The resulting zephyr.dts file contains this setting:
in <devicetree_unfixed...
