void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I have 3 estimote beacons which I want to scan using nrF52833 and display scan response data on Segger RTT viewer and I don't want to establish the connection between...
Hello,
i've made a custom shield plugged into the thingy: 52.
There is a tag connect connector on it. I have short SWD signal from thingy debug connector.
When i try...
Hey,
Is it not possible to use any Bluetooth status codes for disconnection when calling sd_ble_gap_disconnect ?
for example this is not working (I do not actually disconnect...
Hi,
Similar as this issue
Our QA team found the nRF9160 device will hang when user pull out the USIM card then try to deactivate LTE.
The issue can be repoduced by following...
We tested this issue on serial_lte_modem sample on NCS 1.2 and modem mfw_nrf9160_1.2.0
1, Enable CSCON unsolicited report:
AT+CSCON=2
2, Activate LTE search and connect...
Hi,
My problem in shortly is when I have debugger connected to nRF5282, I always get hardfault after some time.
https://i.ibb.co/hZ3bZ1b/optionbytes-1.png
I tried...
hi .i use the pca10056 connect to th nrfconnect by usb .andr dun the app Bluetooth low energy.other 52840 device run the hex of \nordic
sdk\nRF5_SDK_16.0.0_98a08e2\examples...
Hello,
I'am working with a project and want to maximize ble throughput from ble thingy52 to a central device. I have used the ble sniffer with wireshark to see data transfer...
Hi Team,
i am working on serial LTE modem sample project trying to send at commands through serial lte link monitor, found that device is not responding to at commands...
Hi,
Recently I updated nRF Toolbox iOS to 5.0.1.
I'm mainly using this tool for writing application via DFU to nRF51822 board.
I was using .hex files for DFU but I can...
Hi,
I am working on a product based on an nRF52832 (SDK 15.3, Softdevice S112 v6.1).
For security purposes, I would like to restrict the pairing / bonding procedure to...
Hello, guys!
I am using master branch of nRF Connect SDK and want to use UART_1 module of nRF9160 SiP to communicate with external devices.
I used nrf9160_pca10090ns.overlay...
Hello, I am evaluating different printed antenna options for my Nordic design using nRF52 series ICs. The small size of the meandered antenna used in the nRF24LU1 USB dongle...
Hi,
I am on SDK 15.2 and NRF52832. I think that I am quite stupid because I do not succeed to be in Non-scannable non-connectable mode.
I tried few stuffs, change directly...
