Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
hi,
I am using nrf52840 (in a Laird module) and trying to advertise such that legacy BLE 4 mobile devices can connect. Only BLE 5 mobile can see the device (running nRFConnect...
Hi, I have a problem with the reset pin not working on the nrf52811. The firmware was developed on the nrf52840dk board and now that we are migrating to the real nrf52811...
Hello,
I have one SPI instance (instance 3, but have tried others) reading data from an ADC. It's reading data from an ADC triggered by a DRDY signal at 25khz. I setup a...
Hi,
I just enabled the CONFIG_BOOTLOADER_MCUBOOT=y for serial LTE modem application to understand the flash partitions and to perform the serial DFU(not sure if its really...
Hallo, using nRF52840 DK with Keil uVision 5.30, I try to debug the example ble_app_uart in the folder ble_peripheral, pca10056, s140. Compilation is OK, erase/programming...
please help me
I was working with LPCOMP when I set up lpcomp like above, even though I have set my comparator but just impacting anything on the AIN2 pin...
Hi,
I am using nrf52832 mesh board.I want to unprovision the device by pressing the button on the board.In the lc server example they handled it in rtt as it dont have hal...
Hello everyone, I am Smit and I am an IOS developer.
I am stuck to write data into the BLE device. Can anyone please help me out with this? Can anyone tell me how to do...
Hi,
I used the command line to install the toolchains as follows:
sudo apt install gcc-arm-none-eabi
It then installed version 9.3.1 of the tools on my Linux ubuntu...
Hi,
We have implemented a custom Watchdog Timeout handler, where we do the stack-dump. It has worked fine and we were able to analyze and fix the Watchdog resets. But...
Hi,
We are using some nRF52 DKs for debugging and programming prototype boards. Everything went fine until we wanted to expand our testing setup and got some new nRF52...
Hello team, I want to use Normal Sleep mode that is (__WFE) normal sleep mode in NRF51822 using MBED OS 2. But, when ever I am using this method, my code has been waiting...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
The following vulnerability "CVE-2020-10135" has been reported by the Bluetooth SIG. Will this device be affected...
Hello
I am using SDK v17 and sending the value of acceleration sensor to the app.
I want to use this value to process some action in the app. For example, if the transmitted...
